Hi,
it is exactly what I typically do. The IP core is provided with the following input/output signals (I use vhdl not verilog):
PIM_Addr : OUT std_logic_vector(31 downto 0);
PIM_AddrReq : OUT std_logic;
PIM_AddrAck : IN std_logic;
PIM_RNW : OUT std_logic;
PIM_Size : OUT std_logic_vector(3 downto 0);
PIM_RdModWr : OUT std_logic;
PIM_WrFIFO_Data : OUT std_logic_vector(31 downto 0);
PIM_WrFIFO_BE : OUT std_logic_vector(3 downto 0);
PIM_WrFIFO_Push : OUT std_logic;
PIM_RdFIFO_Data : IN std_logic_vector(31 downto 0);
PIM_RdFIFO_Pop : OUT std_logic;
PIM_RdFIFO_RdWdAddr : IN std_logic_vector(3 downto 0);
PIM_WrFIFO_Empty : IN std_logic;
PIM_WrFIFO_AlmostFull : IN std_logic;
PIM_WrFIFO_Flush : OUT std_logic;
PIM_RdFIFO_Empty : IN std_logic;
PIM_RdFIFO_Flush : OUT std_logic;
PIM_RdFIFO_Latency : IN std_logic_vector(1 downto 0);
PIM_InitDone : IN std_logic;
Then I add the following lines to the mpd file of the IP core :
## PIM NPI Interface
BUS_INTERFACE BUS = MPMC_PIM, BUS_STD = XIL_NPI, BUS_TYPE = INITIATOR
PORT PIM_Addr = Addr, DIR = O, BUS = MPMC_PIM, VEC = [31:0]
PORT PIM_AddrReq = AddrReq, DIR = O, BUS = MPMC_PIM
PORT PIM_AddrAck = AddrAck, DIR = I, BUS = MPMC_PIM
PORT PIM_RNW = RNW, DIR = O, BUS = MPMC_PIM
PORT PIM_Size = Size, DIR = O, BUS = MPMC_PIM, VEC = [3:0]
PORT PIM_RdModWr = RdModWr, DIR = O, BUS = MPMC_PIM
PORT PIM_WrFIFO_Data = WrFIFO_Data, DIR = O, BUS = MPMC_PIM, VEC = [31:0]
PORT PIM_WrFIFO_BE = WrFIFO_BE, DIR = O, BUS = MPMC_PIM, VEC = [3:0]
PORT PIM_WrFIFO_Push = WrFIFO_Push, DIR = O, BUS = MPMC_PIM
PORT PIM_RdFIFO_Data = RdFIFO_Data, DIR = I, BUS = MPMC_PIM, VEC = [31:0]
PORT PIM_RdFIFO_Pop = RdFIFO_Pop, DIR = O, BUS = MPMC_PIM
PORT PIM_RdFIFO_RdWdAddr = RdFIFO_RdWdAddr, DIR = I, BUS = MPMC_PIM, VEC = [3:0]
PORT PIM_WrFIFO_Empty = WrFIFO_Empty, DIR = I, BUS = MPMC_PIM
PORT PIM_WrFIFO_AlmostFull = WrFIFO_AlmostFull, DIR = I, BUS = MPMC_PIM
PORT PIM_WrFIFO_Flush = WrFIFO_Flush, DIR = O, BUS = MPMC_PIM
PORT PIM_RdFIFO_Empty = RdFIFO_Empty, DIR = I, BUS = MPMC_PIM
PORT PIM_RdFIFO_Flush = RdFIFO_Flush, DIR = O, BUS = MPMC_PIM
PORT PIM_RdFIFO_Latency = RDFIFO_Latency, DIR = I, BUS = MPMC_PIM, VEC = [1:0]
PORT PIM_InitDone = InitDone, DIR = I, BUS = MPMC_PIM
Now, you can enable a port in the MPMC instance, configure it to support NPI protocol and connect it to the port of your IP.
Regards
Mariano
