cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
ncutcx
Visitor
Visitor
513 Views
Registered: ‎07-11-2019

ZCU104 gst-launch-1.0 xlnxroivideo1detect error

在ZCU104上创建工程,增加DPU后,通过

dexplorer -w 可以看到DPU已经加载如下:

root@vcu_roi_trd-2020_1:/# dexplorer -w

[DPU IP Spec]

IP  Timestamp            : 2020-06-18 12:00:00

DPU Core Count           : 1

 

[DPU Core Configuration List]

DPU Core                 : #0

DPU Enabled              : Yes

DPU Arch                 : B4096

DPU Target Version       : v1.4.1

DPU Freqency             : 300 MHz

Ram Usage                : Low

DepthwiseConv            : Enabled

DepthwiseConv+Relu6      : Enabled

Conv+Leakyrelu           : Enabled

Conv+Relu6               : Enabled

Channel Augmentation     : Enabled

Average Pool             : Enabled

但当运行 gst-launch-1.0 v4l2src device=/dev/video0 ! video/x-raw, width=3840, height=2160, framerate=60/1 ! xlnxroivideo1detect capture-io-mode=4 output-io-mode=5 relative-qp=-21 ! kmssink bus-id=a00c0000.v_mix fullscreen-overlay=1 时出现如下错误:

Setting pipeline to PAUSED ...

WARNING: Logging before InitGoogleLogging() is written to STDERR

F0408 10:36:43.325525 18784 op_def_factory_imp.cpp:79] [UNILOG][FATAL][/proj/rdi/builds/vitis-ai/Vitis-AI-1.2/XIR/1.2/12/src/xir/op/op_def_factory_imp.cpp:79][XIR_UNREGISTERED_OP][Unregistered operator!] upload

*** Check failure stack trace: ***

Aborted

我在github 上没有找到Vitis-AI-1.2/XIR/1.2/12/src/xir/op/op_def_factory_imp.cpp的代码,也不知道是什么没有注册成功。请问这是什么原因导致?

 

0 Kudos
4 Replies
fgbzr
Visitor
Visitor
385 Views
Registered: ‎11-27-2020

I have the same problem on the zcu106.

Did you find a solution ?

0 Kudos
taytoon
Observer
Observer
300 Views
Registered: ‎03-10-2021

Same problem too ..

0 Kudos
buaaneo
Observer
Observer
255 Views
Registered: ‎01-27-2021

I have the same problem. Have you solved it?

0 Kudos
chaoz
Xilinx Employee
Xilinx Employee
223 Views
Registered: ‎09-14-2018

In XIR v1.2, there is no 'upload' operator, but the compiled xmodel they use is not compiled under XIR v1.2, may be under higher version.

op "upload" and "download" are added since the 1.3 release

----------------------------------------------------------------------------------------------
Don't forget to "Accept as solution" or "Kudo" if it helps. Thanks!
----------------------------------------------------------------------------------------------

Chao
----------------------------------------------------------------------------------------------
如果帖子有帮助,别忘“接受为解决方案”或“奖励”。谢谢!
Don't forget to "Accept as solution" or "Kudo" if it helps. Thanks!
----------------------------------------------------------------------------------------------
0 Kudos