UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Participant sharpwind
Participant
173 Views
Registered: ‎12-07-2008

WARNING:iMPACT:923 cann't find JTAG cable on using ISE14.7, WIN10

Jump to solution

Hi,

I am still getting this problem,have u have a definate answer to it now?

I have done everything according to AR#54381(uninstall and re-install) but didn't help. this picture shows that the driver is actually well installed.

11.jpg

I have also a vivado 2016.4 installed, which can download bit file to FPGA well.

is this some way that u are sweeping out ISE users?

 

0 Kudos
1 Solution

Accepted Solutions
Participant sharpwind
Participant
56 Views
Registered: ‎12-07-2008

Re: WARNING:iMPACT:923 cann't find JTAG cable on using ISE14.7, WIN10

Jump to solution
I have fixed the problem. and my guess is right, it is because the 64bit ISE is not properly installed. I followed this : Open the following directory: C:\Xilinx\14.7\ISE_DS\ISE\lib\nt64 Find and rename libPortability.dll to libPortability.dll.orig Make a copy of libPortabilityNOSH.dll (copy and paste it to the same directory) and rename it libPortability.dll Copy libPortabilityNOSH.dll again, but this time navigate to C:\Xilinx\14.7\ISE_DS\common\lib\nt64 and paste it there In C:\Xilinx\14.7\ISE_DS\common\lib\nt64 Find and rename libPortability.dll to libPortability.dll.orig Rename libPortabilityNOSH.dll to libPortability.dll now I can use the 64bit ISE and download bit fine. thank you!
0 Kudos
6 Replies
Moderator
Moderator
148 Views
Registered: ‎06-05-2013

Re: WARNING:iMPACT:923 cann't find JTAG cable on using ISE14.7, WIN10

Jump to solution
Can you check if the default cable setup for ISE is Digilent by any chance?
Use Impact> output> Cable setup> Set it to the platform cable.

If you can use for Vivado then Impact should be able to detect the cable.

Does the LED goes green?

Thanks
Harshit
-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
0 Kudos
Participant sharpwind
Participant
134 Views
Registered: ‎12-07-2008

Re: WARNING:iMPACT:923 cann't find JTAG cable on using ISE14.7, WIN10

Jump to solution

yes, the led is green.

无标题.jpg

无标题.jpg
0 Kudos
Moderator
Moderator
123 Views
Registered: ‎06-05-2013

Re: WARNING:iMPACT:923 cann't find JTAG cable on using ISE14.7, WIN10

Jump to solution
Is this a Spartan 6 version of ISE supported on Windows 10? Then you should be using Spartan 6.

Next try to select platform cable II instead of platform cable IV.

- Harshit
-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
0 Kudos
Participant sharpwind
Participant
74 Views
Registered: ‎12-07-2008

Re: WARNING:iMPACT:923 cann't find JTAG cable on using ISE14.7, WIN10

Jump to solution
hi, sorry for the delay. when i select platform cable II , there is nothing in the "port" combobox. On other computers, i can see USB1 and select the port speed.
捕获.JPG
0 Kudos
Participant sharpwind
Participant
64 Views
Registered: ‎12-07-2008

Re: WARNING:iMPACT:923 cann't find JTAG cable on using ISE14.7, WIN10

Jump to solution

another behavior that might be related to this issue is that after install, I cann't open the 64bit ISE and and cann't open impact alone. I can just open the 32bit ISE and open impact within ISE.

so i guess https://www.xilinx.com/support/answers/54381.html cann't help me, because all the install and uninstall are in the n64 folder. but if I try to do the similar install/uninstall command, some errors will come out, telling me that i am not allowed to execute a x86 command on the x64 platform

F:\Xilinx\14.7\ISE_DS\ISE\bin\nt>wdreg -inf windrvr6.inf install
WDREG utility v10.21. Build Aug 31 2010 14:42:01
Error: Cannot run an x86 build of this utility on x64 platform.
Error: Initializing driver failed

F:\Xilinx\14.7\ISE_DS\ISE\bin\nt> wdreg -inf xusbdrvr.inf install
WDREG utility v10.21. Build Aug 31 2010 14:42:01
Error: Cannot run an x86 build of this utility on x64 platform.
Error: Initializing driver failed

0 Kudos
Participant sharpwind
Participant
57 Views
Registered: ‎12-07-2008

Re: WARNING:iMPACT:923 cann't find JTAG cable on using ISE14.7, WIN10

Jump to solution
I have fixed the problem. and my guess is right, it is because the 64bit ISE is not properly installed. I followed this : Open the following directory: C:\Xilinx\14.7\ISE_DS\ISE\lib\nt64 Find and rename libPortability.dll to libPortability.dll.orig Make a copy of libPortabilityNOSH.dll (copy and paste it to the same directory) and rename it libPortability.dll Copy libPortabilityNOSH.dll again, but this time navigate to C:\Xilinx\14.7\ISE_DS\common\lib\nt64 and paste it there In C:\Xilinx\14.7\ISE_DS\common\lib\nt64 Find and rename libPortability.dll to libPortability.dll.orig Rename libPortabilityNOSH.dll to libPortability.dll now I can use the 64bit ISE and download bit fine. thank you!
0 Kudos