cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
deppenkaiser
Contributor
Contributor
5,990 Views
Registered: ‎06-28-2016

Vivado 2017.3 IP-Upgrade

Jump to solution

Hello,

 

i wish to use an example Project for my arty-z-20 board. The example was made for an earlier Vivado Version. Now Vivado tells me, that i have to update some used ip`s but they are locked.

 

How can i unlock the given ip`s and update them?

 

Thank you...

 

0 Kudos
1 Solution

Accepted Solutions
thakurr
Moderator
Moderator
7,086 Views
Registered: ‎09-15-2016

Hi @deppenkaiser

 

Please use the below command:

upgrade_ip [get_ips]

Refer page, 1522 of the below link for more information on this:

https://www.xilinx.com/support/documentation/sw_manuals/xilinx2017_1/ug835-vivado-tcl-commands.pdf

 

In the Vivado GUI you can also go to Tool-->Report-->Report IP status and update the same. Refer page 52 of the below link as well:

https://www.xilinx.com/support/documentation/sw_manuals/xilinx2017_3/ug896-vivado-ip.pdf

 

Regards

Rohit

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------

 

 

Regards
Rohit
----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------

View solution in original post

2 Replies
thakurr
Moderator
Moderator
7,087 Views
Registered: ‎09-15-2016

Hi @deppenkaiser

 

Please use the below command:

upgrade_ip [get_ips]

Refer page, 1522 of the below link for more information on this:

https://www.xilinx.com/support/documentation/sw_manuals/xilinx2017_1/ug835-vivado-tcl-commands.pdf

 

In the Vivado GUI you can also go to Tool-->Report-->Report IP status and update the same. Refer page 52 of the below link as well:

https://www.xilinx.com/support/documentation/sw_manuals/xilinx2017_3/ug896-vivado-ip.pdf

 

Regards

Rohit

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------

 

 

Regards
Rohit
----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------

View solution in original post

syedz
Moderator
Moderator
5,979 Views
Registered: ‎01-16-2013

@deppenkaiser,


Check Appendix A at page 86 in below UG:

https://www.xilinx.com/support/documentation/sw_manuals/xilinx2017_3/ug896-vivado-ip.pdf#page=86 

 

Also check page 52: https://www.xilinx.com/support/documentation/sw_manuals/xilinx2017_3/ug896-vivado-ip.pdf#page=52 

 

--Syed

---------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.
Give Kudos to a post which you think is helpful and reply oriented.

Did you check our new quick reference timing closure guide (UG1292)?
---------------------------------------------------------------------------------------------
0 Kudos