UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Xilinx Employee
Xilinx Employee
1,767 Views
Registered: ‎07-08-2013

Using IDF and Partial Reconf on Zynq UltraScale+ and Zynq-7000

Jump to solution

Is it possible to combine IDF and PR flow with ZU+ and/or Zynq-7000?

If so, which Vivado version is required?

 

Thanks & best regards

Ralph

0 Kudos
1 Solution

Accepted Solutions
Highlighted
Moderator
Moderator
1,792 Views
Registered: ‎02-07-2008

Re: Using IDF and Partial Reconf on Zynq UltraScale+ and Zynq-7000

Jump to solution

Hi @ralphb, when you say combine, do you mean use IDF and PR in same design? If yes, then with Zynq-7000, it’s possible now with 2018.2.

 

For Zynq UltraScale+, it’s in development, with the possibility of adding support sometime next year.

-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
5 Replies
Highlighted
Moderator
Moderator
1,793 Views
Registered: ‎02-07-2008

Re: Using IDF and Partial Reconf on Zynq UltraScale+ and Zynq-7000

Jump to solution

Hi @ralphb, when you say combine, do you mean use IDF and PR in same design? If yes, then with Zynq-7000, it’s possible now with 2018.2.

 

For Zynq UltraScale+, it’s in development, with the possibility of adding support sometime next year.

-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
1,505 Views
Registered: ‎08-13-2015

Re: Using IDF and Partial Reconf on Zynq UltraScale+ and Zynq-7000

Jump to solution

Hello,

 

I am interested in using Isolation Flow with Partial Reconfiguration with Zynq-7000.

 

Please can you explain what are the new features of Vivado 2018.2 allowing using both flow in combination ?

 

Thank you

 

Mathieu

0 Kudos
Observer toku
Observer
1,304 Views
Registered: ‎08-30-2017

Re: Using IDF and Partial Reconf on Zynq UltraScale+ and Zynq-7000

Jump to solution

Hi,

 

I tried to use IDF und PR in the same blockdesign with tcl-Flow for PR for Zynq 7000 und Zynq UltraScale+.

 

In both cases I receive the error: "Peconfigurabel cell 'my_module_wrp' has both properties HD.RECONFIGURABLE and HD.ISOLATED set. For partial reconfigurable cell, is not allowed to have other flow properties set, such as HD.ISOLated, HD.PARTITION, and HD.TANDEM. Please reset non-HD.RECONFIGURABLE properties."

 

Could you please tell me how is it possible to have IDF and PR in the same design on the same wrapper?

Thank you!

Bildschirmfoto von 2018-11-05 15-37-09.png
0 Kudos
Observer toku
Observer
1,029 Views
Registered: ‎08-30-2017

Re: Using IDF and Partial Reconf on Zynq UltraScale+ and Zynq-7000

Jump to solution

Hi,

I talked to Xilinx und got this answer (11.12.2018):
"Currently, the combined flow IDF + PR is being evaluated, with the objective of it being supported for ZUS+, in 2019.2. The Vivado version in which this flow will be officially supported in, is however, subject to change.

 This flow will not be supported for Zynq-7000."

 

Conclusion:
IDF and PR can not be combined in the same design.
Neither for Znyq 7000 nor for Zynq UltraScale+.

0 Kudos
1,019 Views
Registered: ‎08-13-2015

Re: Using IDF and Partial Reconf on Zynq UltraScale+ and Zynq-7000

Jump to solution

Thank you for your message !

Mathieu

0 Kudos