cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
vignesh99
Observer
Observer
912 Views
Registered: ‎10-03-2019

Cannot boot Petalinux on xilinx ZCU102

Hi I am trying to run petalinux on xilinx zcu102. I downloaded the image file from:  https://www.xilinx.com/products/design-tools/ai-inference/ai-developer-hub.html#edge

I have extracted the image file and installed it in the memory card with win32diskImager.

It gives me the following error when I try to log in and boot up via putty

U-Boot 2019.01 (Aug 01 2019 - 10:37:25 +0000)

Model: ZynqMP ZCU102 Rev1.0
Board: Xilinx ZynqMP
DRAM: 4 GiB
EL Level: EL2
Chip ID: zu9eg
MMC: mmc@ff170000: 0
Loading Environment from FAT... sdhci_send_command: MMC: 0 busy timeout increasing to: 200 ms.
sdhci_send_command: MMC: 0 busy timeout increasing to: 400 ms.
sdhci_send_command: MMC: 0 busy timeout increasing to: 800 ms.
sdhci_send_command: MMC: 0 busy timeout increasing to: 1600 ms.
sdhci_send_command: MMC: 0 busy timeout increasing to: 3200 ms.
sdhci_send_command: MMC: 0 busy timeout.
sdhci_send_command: MMC: 0 busy timeout.
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_send_command: MMC: 0 busy timeout.
In: serial@ff000000
Out: serial@ff000000
Err: serial@ff000000
Model: ZynqMP ZCU102 Rev1.0
Board: Xilinx ZynqMP
Bootmode: LVL_SHFT_SD_MODE1
Reset reason: EXTERNAL
Net: ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id

Warning: ethernet@ff0e0000 (eth0) using random MAC address - 96:f1:3b:71:cd:2b
eth0: ethernet@ff0e0000
U-BOOT for xilinx-zcu102-2019_1

ethernet@ff0e0000 Waiting for PHY auto negotiation to complete......................................... TIMEOUT !
Hit any key to stop autoboot: 0
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_send_command: MMC: 0 busy timeout.
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_set_clock: Timeout to wait cmd & data inhibit
sdhci_send_command: MMC: 0 busy timeout.

Why is this happening? I have tried with other new sd card too, but it shows the same error and doesnt boot.

Please Help. Thank you 

0 Kudos
2 Replies
900 Views
Registered: ‎07-23-2019

0 Kudos
aantonie
Visitor
Visitor
820 Views
Registered: ‎10-30-2018

Hi,

Please read article https://forums.xilinx.com/t5/Embedded-Linux/Cannot-boot-Petalinux-on-xilinx-ZCU102/td-p/1054943 with sd card checklist.

There are described typicall problems with sd card.

Very often there is a need to add to system-user.dtsi following lines:

&sdhc1{
no-1-8-v;
};

no-1-8-v;

0 Kudos