UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Visitor piotr.gregor
Visitor
7,480 Views
Registered: ‎10-24-2013

How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

Hi,

I downloaded

 

Digilent-atlys-v2013.04-final.bsp

 

from Downloads page of Xilinx, however after 

 

tar zxf Digilent-atlys-v2013.04-final.bsp

 

only hardware folder was created, no "petalinux" dir, and no "settings.sh" script.

what steps are required to install petalinux on this board?

I am using Xilinx ISE on Ubuntu 12.10 and I create projects and program them on FPGA successfully.

0 Kudos
1 Solution

Accepted Solutions
Xilinx Employee
Xilinx Employee
9,684 Views
Registered: ‎08-02-2007

Re: How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

Hi,

 

To use this BSP you need to install Petalinux.

 

Please follow the documentation as shown here. http://www.xilinx.com/publications/products/petalinux/petalinux-installation-guide.pdf

 

--HS

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------

View solution in original post

0 Kudos
7 Replies
Xilinx Employee
Xilinx Employee
7,461 Views
Registered: ‎08-02-2007

Re: How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

Hi,

 

The procedure is to use petalinux-install-bsp. This is documented in page 6 of this document

 

 

http://www.xilinx.com/publications/products/petalinux/petalinux-installation-guide.pdf

 

Check the attached snapshot for example

 

--HSpetalinux_install_bsp.png

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------
0 Kudos
Visitor piotr.gregor
Visitor
7,456 Views
Registered: ‎10-24-2013

Re: How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

there is no such tool, I downloaded 

Digilent-atlys-v2013.04-final.bsp 

I did tar this and there is no 

petalinux-install-bsp script. Should I download another bsp and call instalation script pointing to my file bsp?

0 Kudos
Xilinx Employee
Xilinx Employee
7,448 Views
Registered: ‎08-02-2007

Re: How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

Hi,

 

Which version of petalinux are you using?

 

--HS

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------
0 Kudos
Visitor piotr.gregor
Visitor
7,435 Views
Registered: ‎10-24-2013

Re: How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

Hi,

I don't have any petalinux! As I said I just downloaded and tar bsp file as described on Xilinx site

and here \http://www.wiki.xilinx.com/PetaLinux+Installation

I did steps 1,2,3,4 and I did

tar zxf Digilent-atlys-v2013.04-final.bsp

(note this is not Digilent-atlys-v2013.04-final-full.bsp  there is no such file to download)

and next it is said to do source settings or someone else said to run petalinux command but I have no petalinux folder or program installed.

 

do I have to install petalinux other way and then install bsp?

0 Kudos
Xilinx Employee
Xilinx Employee
9,685 Views
Registered: ‎08-02-2007

Re: How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

Hi,

 

To use this BSP you need to install Petalinux.

 

Please follow the documentation as shown here. http://www.xilinx.com/publications/products/petalinux/petalinux-installation-guide.pdf

 

--HS

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------

View solution in original post

0 Kudos
Visitor piotr.gregor
Visitor
7,419 Views
Registered: ‎10-24-2013

Re: How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

OK, I have missed the petalinux archive and downloaded only BSP files.

"click on the appropriate links to download the 'PetaLinux XX.YY installation archive' and all required BSPs."

 

thank you

0 Kudos
Highlighted
7,263 Views
Registered: ‎11-29-2013

Re: How to install petalinux on Digilent Atlys Spartan6 LX45 FPGA

Jump to solution

I'm trying to load a prebuilt kernel image and I have an issue, I'm  usin Ise Design tools 13.2 and Petalinux SDK 13.04, could I have a problem with ther versions??

 

Thanks

 

LEVEL 3 BOOT:
Configuring the FPGA...
FPGA configuration completed.
Downloading and booting Linux Kernel from RAM memory, this may take a few minutes.
Launching XMD for file download and boot.
This may take a few minutes, depending on the size of your image.
WARNING: es_AR:es is not supported as a language.  Using usenglish.
ERROR: Unable to download the image
Done..
Connect hyperterminal or kermit at 115200 baud.


@piotr.gregor wrote:

OK, I have missed the petalinux archive and downloaded only BSP files.

"click on the appropriate links to download the 'PetaLinux XX.YY installation archive' and all required BSPs."

 

thank you



@piotr.gregor wrote:

OK, I have missed the petalinux archive and downloaded only BSP files.

"click on the appropriate links to download the 'PetaLinux XX.YY installation archive' and all required BSPs."

 

thank you




Login using root/root as the username and password

0 Kudos