UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Visitor mvogt997
Visitor
514 Views
Registered: ‎06-29-2018

Missing MIG simulation file (SIP_PHY_CONTROL) in compiled library for modelsim

I get the following error when running Modelsim after compiling libraries for a Spartan 7-25.  I am using Vivado 2018.2 and Modelsim 10.2a.  SIP_PHY_CONTROL in instantiated by phy_control.v.

# Loading unisims_ver.PHY_CONTROL
# ** Error: (vsim-3033) C:/Xilinx/Vivado/2018.2/data/verilog/src/unisims/PHY_CONTROL.v(569): Instantiation of 'SIP_PHY_CONTROL' failed. The design unit was not found.
#
# Region: /sim_tb_top/u_ip_top/u_mig_7series_0/u_mig_7series_0_mig/u_memc_ui_top_axi/mem_intfc0/ddr_phy_top0/u_ddr_mc_phy_wrapper/u_ddr_mc_phy/ddr_phy_4lanes_0/u_ddr_phy_4lanes/phy_control_i
# Searched libraries:
# C:/Users/user/Data/Technology/Electrical/FPGA/ArtyS7/Proj-25/MIG_25_1/MIG_25_1.sim/sim_1/behav/modelsim/modelsim_lib/msim/xil_defaultlib
# C:/Users/user/Data/Technology/Electrical/FPGA/ArtyS7/Proj-25/MIG_25_1/MIG_25_1.cache/compile_simlib/modelsim/unisims_ver
# C:/Users/user/Data/Technology/Electrical/FPGA/ArtyS7/Proj-25/MIG_25_1/MIG_25_1.cache/compile_simlib/modelsim/unimacro_ver
# C:/Users/user/Data/Technology/Electrical/FPGA/ArtyS7/Proj-25/MIG_25_1/MIG_25_1.cache/compile_simlib/modelsim/secureip
# C:/Users/user/Data/Technology/Electrical/FPGA/ArtyS7/Proj-25/MIG_25_1/MIG_25_1.cache/compile_simlib/modelsim/xpm
# C:/Users/user/Data/Technology/Electrical/FPGA/ArtyS7/Proj-25/MIG_25_1/MIG_25_1.cache/compile_simlib/modelsim/unisims_ver

Can someone please supply this file?

0 Kudos
4 Replies
Xilinx Employee
Xilinx Employee
469 Views
Registered: ‎09-05-2018

Re: Missing MIG simulation file (SIP_PHY_CONTROL) in compiled library for modelsim

Hey @mvogt997,

I think the problem is actually your Modelsim version. Can you install Mentor Graphic ModelSim SE/DE/PE (10.6c)? This is the compatible tool listed on page 13 of UG973 for Vivado 2018.2.

Nicholas Moellers

Xilinx Worldwide Technical Support
Moderator
Moderator
468 Views
Registered: ‎11-28-2016

Re: Missing MIG simulation file (SIP_PHY_CONTROL) in compiled library for modelsim

Hello @mvogt997

Modelsim 10.2a is an unsupported version for Vivado 2018.2.  Based on UG973 for Vivado 2018.2 the supported version is ModelSim 10.6c.  It's very likely the simulation issues you're seeing are due to this mismatch.  Here's a link to UG973 for Vivado 2018.2:
https://www.xilinx.com/support/documentation/sw_manuals/xilinx2018_2/ug973-vivado-release-notes-install-license.pdf

supported_sim_versions.PNG

Visitor mvogt997
Visitor
449 Views
Registered: ‎06-29-2018

Re: Missing MIG simulation file (SIP_PHY_CONTROL) in compiled library for modelsim

Thanks for that.

I assume Modelsim 10.6c or later would work, correct?

Mark

0 Kudos
Moderator
Moderator
436 Views
Registered: ‎11-28-2016

Re: Missing MIG simulation file (SIP_PHY_CONTROL) in compiled library for modelsim

Hello @mvogt997,

I wouldn't assume that a later version would work.  These were the tested versions we know work so anything other than that is an unknown.

0 Kudos