UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Visitor mansura
Visitor
793 Views
Registered: ‎07-26-2017

IBUFDS_GET4.O is locked to GTHE4_common_x0Y2 ZCU102 Dev Board

Jump to solution

Hello Xilinx Folks

 

I am using a ZCU102 eval board to receive aurora data via the SFP port.

I am not sure what to set for the XY options on the Aurora IP. It is very confusing and the documentation is very limited as far as explaining what it means. In the documentation it shows this.

 aurora.jpg

Image above is from Aurora Document for reference.

I am not sure how to find the corresponding locations for the SFP ports on the ZCU102 board. I am using SFP0 and SFP1. Below there is a snip of the schematic as well. How can I cross reference the Aurora 8b10b description as seen in PG046 with the ZCU102 eval board? How to find the proper properties for the Aurora IP as shown below highlighted.

zynq.jpg

Image above is from ZCU102 schematic for reference.

gui.JPG

Image above is from Aurora GUI. not sure what to set for highlighted options.

 

errerr.JPG

Image above is the error I am getting. It is a critical warning that leads to a non rout able clock signal for the aurora.

 

Any help is appreciated.

Thanks

 

 

0 Kudos
1 Solution

Accepted Solutions
Moderator
Moderator
963 Views
Registered: ‎02-16-2010

Re: IBUFDS_GET4.O is locked to GTHE4_common_x0Y2 ZCU102 Dev Board

Jump to solution
Based on ug1075, figure 1-15

I find Quad 230 on ZCU102 board has GT locations from X1Y12-X1Y15.
------------------------------------------------------------------------------
Don't forget to reply, give kudo and accept as solution
------------------------------------------------------------------------------
4 Replies
Moderator
Moderator
964 Views
Registered: ‎02-16-2010

Re: IBUFDS_GET4.O is locked to GTHE4_common_x0Y2 ZCU102 Dev Board

Jump to solution
Based on ug1075, figure 1-15

I find Quad 230 on ZCU102 board has GT locations from X1Y12-X1Y15.
------------------------------------------------------------------------------
Don't forget to reply, give kudo and accept as solution
------------------------------------------------------------------------------
Visitor mansura
Visitor
684 Views
Registered: ‎07-26-2017

Re: IBUFDS_GET4.O is locked to GTHE4_common_x0Y2 ZCU102 Dev Board

Jump to solution

Hello

 

Can you point me to the document where that was found.

 

Thanks

 

0 Kudos
Moderator
Moderator
681 Views
Registered: ‎02-16-2010

Re: IBUFDS_GET4.O is locked to GTHE4_common_x0Y2 ZCU102 Dev Board

Jump to solution
I am not sure I fully understand your question, here is the link to ug1075.
http://www.xilinx.com/support/documentation/user_guides/ug1075-zynq-ultrascale-pkg-pinout.pdf
------------------------------------------------------------------------------
Don't forget to reply, give kudo and accept as solution
------------------------------------------------------------------------------
0 Kudos
Visitor mansura
Visitor
679 Views
Registered: ‎07-26-2017

Re: IBUFDS_GET4.O is locked to GTHE4_common_x0Y2 ZCU102 Dev Board

Jump to solution

That was what I was looking for, the document you reference to find the XY locations.

 

Thanks for the help.

0 Kudos