UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Observer yanghaofei@ni
Observer
333 Views
Registered: ‎10-09-2018

get problem when using eyescan reference design

Jump to solution

hello,

 

i am adding reference design for eyescan test(xapp1198) to my project to test my pcie port.

the method is:

i used the Vivado 2014.4 (which is exactly required in the User Guide and other new versions), and then downloaded source file xapp1198, navigated to the path: /xapp1198/2014.4/KC705/source/ipi_tcl, and then run the tcl file kc705_ipi.tcl in order to generate the eyescan subsystem with ip integrator.

but get the strange error below:

ERROR: [BD 5-216] VLNV <xilinx.com:ip:drp_bridge:1.0> is not supported for this version of the tools.
ERROR: [Common 17-39] 'create_bd_cell' failed due to earlier errors.

    while executing
"create_bd_cell -type ip -vlnv xilinx.com:ip:drp_bridge:1.0 drp_bridge_0 "
    (procedure "create_hier_cell_DRP_Bridge_hier" line 55)
    invoked from within
"create_hier_cell_DRP_Bridge_hier [current_bd_instance .] DRP_Bridge_hier"
    (procedure "create_root_design" line 44)
    invoked from within
"create_root_design """
    (file "./kc705_ipi.tcl" line 512)

could someone help me please.

 

 

 

best regards

0 Kudos
1 Solution

Accepted Solutions
Highlighted
Advisor evgenis1
Advisor
282 Views
Registered: ‎12-03-2007

Re: get problem when using eyescan reference design

Jump to solution

Hi yanghaofei@ni , 

 

I don't think DRP bridge is part of Vivado IP repository. 

 

There is a DRP IP core that is distributed with xapp1198 design. It requires a manual step to add it to Vivado IP search path, so that IP Integrator sees it. 

 

Go to Project Manager -> Settings dialog. Open IP -> Repository. Click on [+]. In the opened dialog, navigate to the location of drp_bridge_ip .xci file, and click "Apply".

 

Hope that helps.

 

Thanks,

Evgeni

 

 

Tags (1)
0 Kudos
3 Replies
Xilinx Employee
Xilinx Employee
287 Views
Registered: ‎08-07-2007

回复: get problem when using eyescan reference design

Jump to solution

hi yanghaofei@ni

 

you can open IP Calalog in Vivado, search for 'drp_bridge', see the version number, for example, say 1.1

 

Edit the tcl file, search for 'xilinx.com:ip:drp_bridge:1.0', and replace drp_bridge:1.0 by drp_bridge:1.1

 

please check if this works.

 

Thanks,

Boris

 

------------------------------------------------------------------------------
Don't forget to reply, give kudo and accept as solution
------------------------------------------------------------------------------
0 Kudos
Highlighted
Advisor evgenis1
Advisor
283 Views
Registered: ‎12-03-2007

Re: get problem when using eyescan reference design

Jump to solution

Hi yanghaofei@ni , 

 

I don't think DRP bridge is part of Vivado IP repository. 

 

There is a DRP IP core that is distributed with xapp1198 design. It requires a manual step to add it to Vivado IP search path, so that IP Integrator sees it. 

 

Go to Project Manager -> Settings dialog. Open IP -> Repository. Click on [+]. In the opened dialog, navigate to the location of drp_bridge_ip .xci file, and click "Apply".

 

Hope that helps.

 

Thanks,

Evgeni

 

 

Tags (1)
0 Kudos
Observer yanghaofei@ni
Observer
272 Views
Registered: ‎10-09-2018

Re: get problem when using eyescan reference design

Jump to solution

it works. thank you so much.

0 Kudos