UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

reVision project for ZCU102 ES2 runing on ZCU102 Production?

Reply
Highlighted
Observer
Posts: 23
Registered: ‎03-21-2018

reVision project for ZCU102 ES2 runing on ZCU102 Production?

[ Edited ]

Hi!

 

I have a Vivado+SDX project based on reVision 2017.2 for zcu102 ES2.

I must buy a zcu102 Production board and I wondered how easy it would be to make my project run on this card ?

Is it enough to change the targeted card or are there other things I must care about ?

 

Thanks in advance,

Alexandre

Xilinx Employee
Posts: 44
Registered: ‎08-20-2018

Re: reVision project for ZCU102 ES2 runing on ZCU102 Production?

[ Edited ]

Hi @alexandre.willeme

 

Please have a look at the hardware requirement below,

Required:

  • ZCU104 Evaluation Board, or
  • ZCU102 Evaluation Board
    • rev 1.0 with ES2 silicon or
    • rev 1.0 with production silicon
  • Micro-USB cable, connected to laptop or desktop computer for the terminal emulator
  • SD card (ZCU102) or
  • micro-SD card (ZCU104)

 

Please refer to the tutorial and other requirements here,

https://github.com/Xilinx/reVISION-Getting-Started-Guide/blob/master/software-tools-system-requirements.md

 

 

Best Regards,

Nutan

 

-----------------------------------------------------------------

Please do not forget to accept as a solution, Kudo

Observer
Posts: 23
Registered: ‎03-21-2018

Re: reVision project for ZCU102 ES2 runing on ZCU102 Production?

Hi @nutang,

 

Thanks for your answer. Nonetheless, I do not think you understand my question correctly. I will try to rephrase it.

I must replace my ZCU102 ES2 by a ZCU102 production I plan to buy. I have a project based on reVision for ZCU102 ES2 with a lot of stuff I made myself inside it. If I want to have this project run on ZCU102 production, do I have to:

1) Only change the target board in Vivado and SDx to ZCU102 production. (which would be easy)

OR

2) Download an original version of the reVision project for ZCU102 production (available on the link you sent me) and add my stuff, one by one, so as to replicate the project that I have currently working on ZCU102 ES2. (which I would like to avoid, of course)

OR

3) Do something else.

 

My bet would be option 1), of course, but I just wanted to check that with you before I actually purchase the ZCU102 production.

 

Thanks in advance,

Alexandre

Observer
Posts: 23
Registered: ‎03-21-2018

Re: reVision project for ZCU102 ES2 runing on ZCU102 Production?

Hi!

Could someone help me? I want to make sure of that before I invest a couple of k$ on this board.
Thanks
Xilinx Employee
Posts: 44
Registered: ‎08-20-2018

Re: reVision project for ZCU102 ES2 runing on ZCU102 Production?

Hi @alexandre.willeme

 

From your description I understood that, you have created your own platform project in SDSoC using your dsa.

 

If I am correct, then, you need to update your vivado project with production board, generate dsa, create new platform project in SDSoC.

 

Then update the platform in your existing project. 

 

I consulted this with expert here, ideally it will work on both.

However, we do our testing only on production platforms.

 

Best Regards,

Nutan