UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Visitor shed82
Visitor
5,302 Views
Registered: ‎03-27-2012

Unable to Program Spartan 3AN

Hi, I am trying to load FPGA program to the board using USB However, when double click on "Program FPGA only" I'm getting following messages. Please advise what's wrong. Is it anything to do with the board jumper? How should i set the jumper for loading using USB. Please advise '1': Loading file 'D:/SAFE/top.bit' ... done. INFO:iMPACT:1777 - Reading C:/Xilinx/13.4/ISE_DS/ISE/spartan3a/data/xc3s700an.bsd... Found sync word in bitstream. UserID read from the bitstream file = 0xFFFFFFFF. INFO:iMPACT:501 - '1': Added Device xc3s700an successfully. ---------------------------------------------------------------------- ---------------------------------------------------------------------- GUI --- Auto connect to cable... INFO:iMPACT - Digilent Plugin: no JTAG device was found. AutoDetecting cable. Please wait. PROGRESS_START - Starting Operation. Connecting to cable (Usb Port - USB21). Checking cable driver. Driver file xusb_emb.sys found. Driver version: src=1029, dest=1029. Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 x86_64 64bit SYS 14:14:44, version = 1021. Cable PID = 0008. Max current requested during enumeration is 74 mA. Type = 0x0004. Cable Type = 3, Revision = 0. Setting cable speed to 6 MHz. Cable connection established. Firmware version = 1303. File version of C:/Xilinx/13.4/ISE_DS/ISE/data/xusb_xlp.hex = 1303. Firmware hex file version = 1303. PLD file version = 0012h. PLD version = 0012h. PROGRESS_END - End Operation. Elapsed time = 0 sec. Type = 0x0004. ESN device is not available for this cable. INFO:iMPACT - Current time: 3/28/2012 8:04:07 AM INFO:iMPACT:583 - '0': The idcode read from the device does not match the idcode in the bsdl File. INFO:iMPACT:1578 - '0': Device IDCODE : 00000100110001010000000100100110 INFO:iMPACT:1579 - '0': Expected IDCODE: 00000010011000101000000010010011 PROGRESS_START - Starting Operation. INFO:iMPACT:583 - '1': The idcode read from the device does not match the idcode in the bsdl File. INFO:iMPACT:1578 - '1': Device IDCODE : 00000100110001010000000100100110 INFO:iMPACT:1579 - '1': Expected IDCODE: 00000010011000101000000010010011 PROGRESS_END - End Operation. Elapsed time = 0 sec.
0 Kudos
5 Replies
Xilinx Employee
Xilinx Employee
5,299 Views
Registered: ‎01-03-2008

Re: Unable to Program Spartan 3AN

Please use the "Insert Code" button (it is the clipboard with the C) on the toolbar when you cut-and-paste so that everything is readable.

 

 Device IDCODE : 00000100110001010000000100100110 
Expected IDCODE: 00000010011000101000000010010011 

 The idcode has been shifted by one position.  This indicates that you have another device in the chain that was not described by your project file or that you have a signal integrity problem with the JTAG chain.

------Have you tried typing your question into Google? If not you should before posting.
Too many results? Try adding site:www.xilinx.com
0 Kudos
Visitor shed82
Visitor
5,280 Views
Registered: ‎03-27-2012

Re: Unable to Program Spartan 3AN

Hi, does it have any thing to do with the jumper settings?

0 Kudos
Xilinx Employee
Xilinx Employee
5,267 Views
Registered: ‎01-03-2008

Re: Unable to Program Spartan 3AN

That would be a question to the person that designed your board.

------Have you tried typing your question into Google? If not you should before posting.
Too many results? Try adding site:www.xilinx.com
0 Kudos
Highlighted
Visitor revkarol
Visitor
5,208 Views
Registered: ‎06-20-2012

Re: Unable to Program Spartan 3AN

I have exactly this issue with the Spartan 3AN starter kit.  I'm trying to program over USB using the Master Serial method and have pins set as in page 39 of the ug334.pdf guide.

 

Please help.

 

Thanks,

Karol.

Tags (1)
0 Kudos
Instructor
Instructor
5,206 Views
Registered: ‎07-21-2009

Please start a new thread

Karol,

 

Please start a new thread.

 

From the New Users Forum README thread:

 

4. Please do not post a new topic or question on someone else's thread -- start a new thread!

 

Interrupting a discussion with an unrelated topic or question is not simply rude, it is considered disrespectful.  This is called hijacking.

  • If your question or topic is unrelated (and unhelpful) to an existing thread, please start a new thread.
  • We want to avoid unreadable threads with 100s of posts which cover topics ranging from power supplies to memory controllers.  Such threads are of no benefit to the users who will follow after you, and a disservice to the creator of the thread who is also seeking help.

 

-- Bob Elkind

SIGNATURE:
README for newbies is here: http://forums.xilinx.com/t5/New-Users-Forum/README-first-Help-for-new-users/td-p/219369

Summary:
1. Read the manual or user guide. Have you read the manual? Can you find the manual?
2. Search the forums (and search the web) for similar topics.
3. Do not post the same question on multiple forums.
4. Do not post a new topic or question on someone else's thread, start a new thread!
5. Students: Copying code is not the same as learning to design.
6 "It does not work" is not a question which can be answered. Provide useful details (with webpage, datasheet links, please).
7. You are not charged extra fees for comments in your code.
8. I am not paid for forum posts. If I write a good post, then I have been good for nothing.
0 Kudos