UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Visitor wadelius
Visitor
1,234 Views
Registered: ‎05-04-2018

Vivado MIPI ip

Jump to solution

Hi, Forum.

I'm about to start a new design and planning to use the Ultrascale+ ZU5 EG or EV.

I have seen a nice dev.kit ZCU104 with an Ultrascale+ ZU7.

My problem is that I want to use the included MIPI ip in Vivado. But those ip's are not compatible.

But they are compatible with ZU3EG, ZU6EG VU3P, KU9P etc

 

Anyone know why I cant use them with the ZU5?

 

best regards

Urban Wadelius

0 Kudos
1 Solution

Accepted Solutions
Moderator
Moderator
1,597 Views
Registered: ‎11-09-2015

Re: Vivado MIPI ip

Jump to solution

Hi @wadelius,

 

All 7-series except spartan-7 are currently supporting MIPI.

 

Only US+ has the HW for the D-PHY in the MIPI. For 7-series, you are expected you use an external PHY as per xapp894.

 

Regards,


Florent
Product Application Engineer - Xilinx Technical Support EMEA
**~ Don't forget to reply, give kudos, and accept as solution.~**
6 Replies
Moderator
Moderator
1,228 Views
Registered: ‎11-09-2015

Re: Vivado MIPI ip

Jump to solution

Hi @wadelius,

 

But they are compatible with ZU3EG, ZU6EG VU3P, KU9P etc

Were did you find this information? As per PG232, I think MIPI is supported on all families starting with 7-series:

MIPI.JPG

 

Note: There are multiple IPs for MIPI:

  • MIPI DPHY
  • MIPI CSI2 RX Subsystem
  • MIPI CSI2 TX Subsystem
  • MIPI DSI TX

But it should be the same for every MIPI IP


Florent
Product Application Engineer - Xilinx Technical Support EMEA
**~ Don't forget to reply, give kudos, and accept as solution.~**
Highlighted
Visitor wadelius
Visitor
1,224 Views
Registered: ‎05-04-2018

Re: Vivado MIPI ip

Jump to solution

Hi Florent,

thanks for quick response.

 

This information was in the Vivado IP tool, but I saw that I use an old one version 2016.2, and maybe that's obsolete information in that version.

 

Does all 7-series support MIPI? I thought only the Ultrascale+ had the right hw to support mipi signal levels?

 

/Urban

 

 

0 Kudos
Moderator
Moderator
1,598 Views
Registered: ‎11-09-2015

Re: Vivado MIPI ip

Jump to solution

Hi @wadelius,

 

All 7-series except spartan-7 are currently supporting MIPI.

 

Only US+ has the HW for the D-PHY in the MIPI. For 7-series, you are expected you use an external PHY as per xapp894.

 

Regards,


Florent
Product Application Engineer - Xilinx Technical Support EMEA
**~ Don't forget to reply, give kudos, and accept as solution.~**
Xilinx Employee
Xilinx Employee
1,125 Views
Registered: ‎03-30-2016

Re: Vivado MIPI ip

Jump to solution

Hello @wadelius

 

@florentw is correct. But I want to add some new information regarding Spartan-7 support.


(D-PHY, CSI-2 TX/RX)

Spartan-7 supported from 2018.1

(DSI TX)

Spartan-7 supported from 2018.3

 

But I would recommended customer to use US+ device for MIPI since it can support D-PHY electrical spec natively.

 

Best regards

Leo

0 Kudos
Adventurer
Adventurer
972 Views
Registered: ‎01-19-2018

Re: Vivado MIPI ip

Jump to solution

We Would appreciate your response.

clk_settle User param value in MIPI CSI-2 Tx IP

In MIPI DHPY {Product Guide 202} Default user parameters in 57 page tells only about HS_SETTLE {8:0 HS_SETTLE_NS R/W 135 + 10 UI} and the default value is 145 ns.
On the other hand, the clk_settle as explained in MIPI_D_PHY specification 548 page requires additional clk_settle param to be initiative. 

More information on Clk_settle param will be quite helpful. It's not given in MIPI CSI-2 Rx or Tx product guides.

Thanks.

0 Kudos
Moderator
Moderator
965 Views
Registered: ‎11-09-2015

Re: Vivado MIPI ip

Jump to solution

Hi @daram123,

 

This is a different question and this topic was not created by you.

 

As per the guidelines for the video board:

4. Do not post a question on someone else's topic. Create a new topic if you have an issue. It might not be the same issue

I am closing this topic for new replies. Please create a new topic for your question.

 

Thank you for you understanding


Florent
Product Application Engineer - Xilinx Technical Support EMEA
**~ Don't forget to reply, give kudos, and accept as solution.~**
0 Kudos