UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Contributor
Contributor
1,088 Views
Registered: ‎10-17-2013

ZCU102 BOARD UI test failed!

I have a zcu102 board;  When i used the board to run dp demo , it didn't display with error message as below:

1st power wake-up - AUX write failed.

2nd power wake-up - AUX write failed.

then i check the schemactic , and found that gtr has combine design for pcie & dp ; 

i use  BoardUI.exe to modify MSP430 setting for dp;

it doesn't work well;

instead , i use BIT.exe to do boardtest , the test result is failed as below :

Error: Found regular expression in step 3 of test 0 - "(.*)Error(.*)"

Error: Could not find regular expression in step 3 of test 0 - "(.*)File\s+sent\s+successfully"

Info: This step started at: 2019-07-19 15:33:01

Error: Stopped because step 3 failed in test 0

step finished

Error: Could not find regular expression in step 0 of test 0 - "(.*)MSP v1.50 I2C Bridge v1.50(.*)"

Info: Result for step 0: Fail
Info: Result for step 1: Pass
Info: Result for step 2: Pass
Info: Result for step 3: Fail
Info: The test took 0 hours, 00 minutes, and 31 seconds. 0:00:31

 

my zcu102 board vertion is 1.1 , product batch is : 0432055-05-1911 

thk

 

 

0 Kudos
22 Replies
Xilinx Employee
Xilinx Employee
1,034 Views
Registered: ‎06-21-2018

Re: ZCU102 BOARD UI test failed!

Hi luodicaizi,

Can you provide a screenshot of your BoardUI.exe like the one below?

To get the Right Pane, click on Layout -> and uncheck "Hide Right Pane"

BIT_tests.png

Thanks,
Andres

0 Kudos
Contributor
Contributor
1,016 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

 
error.jpg
0 Kudos
Contributor
Contributor
1,015 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

 
微信图片_20190723172911.jpg
0 Kudos
Contributor
Contributor
1,013 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

 
微信图片_20190723173208.jpg
0 Kudos
Xilinx Employee
Xilinx Employee
993 Views
Registered: ‎06-21-2018

Re: ZCU102 BOARD UI test failed!

0 Kudos
Contributor
Contributor
971 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

 
1563943870(1).png
0 Kudos
Contributor
Contributor
968 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

cp2108 's driver is already newest!

1563943826(1).png
0 Kudos
Contributor
Contributor
963 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

use board UI you referd,  it still stop here!!

Starting IDCODE/FW Check at: 2019-07-24 13:03:02.635000
Starting step tcl
==========

Exception in thread Thread-2:
Traceback (most recent call last):
File "threading.py", line 801, in __bootstrap_inner
File "testthread.py", line 85, in run
File "testthread.py", line 206, in runbutton
File "testthread.py", line 785, in shell
UnicodeEncodeError: 'ascii' codec can't encode characters in position 1-6: ordinal not in range(128)

1563944723(1).png
0 Kudos
Xilinx Employee
Xilinx Employee
937 Views
Registered: ‎06-21-2018

Re: ZCU102 BOARD UI test failed!

It seems it doesn't even run the tcl script.

If you connect the board to Vivado Hardware Manager, does it detect it correctly?

Thanks,
Andres

 

0 Kudos
Contributor
Contributor
925 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

It is able to connect to the board! even I can use logic analysis to debug probe ;

1564016679.png
0 Kudos
Contributor
Contributor
923 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

Is it necessary to connect PMOD headers & connect PROTO header before do test ;

1564017056(1).png
0 Kudos
Xilinx Employee
Xilinx Employee
902 Views
Registered: ‎06-21-2018

Re: ZCU102 BOARD UI test failed!

Hi luodicaizi84,

You don't need to connect any additional HW besides the 2 microUSB Cables.

I think there might be something related to the text strings, since your Windows OS is on a different language.

Please try these 2 things:

1) Install the 6.7.0.0 driver instead of 6.7.1.0 (even though it says it's only for Windows XP/Server 2003/Vista/7/8/8.1):
https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers

2) Go to File --> Change the Config Variables and type them yourself, like shown here:

BoardUI - change variables.PNG

and File --> Change the System Controller Port

BoardUI - system controller port.PNG

Where this is what my Device Manager looks like:

COM Ports 2.png

Let us know if that helps.

Thanks,
Andres

0 Kudos
Highlighted
Participant subu.rama
Participant
810 Views
Registered: ‎07-22-2018

Re: ZCU102 BOARD UI test failed!

I have the same issue. I have a ZCU102 Rev 1.1 and am using XTP433, Vivado, SCGUI etc. that are 2019.1

I uninstalled the newer Si drivers and installed the v6.7 as suggested.

https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers

image.pngOlder VCP driversHere is what device manager shows (on Windows 10):

image.png

The driver still shows up as: 6.7.4.261 dated 9/19/2016

image.png

So where is the version 6.7.0.0 of the drivers?

Also the new Board UI does NOT have fields for setting the configuration variables fpgaport0, fpgaport1 or fpgaport2.

image.png

And I get a very helpful version information in About: (1986 - Present) :-)

image.png

And of course, I can't even get the Board information.

image.png

I don't have what the 

['COM3', 'COM1', 'COM4', 'COM8', 'COM9', 'COM10'] line refers to in the right hand pane but I get it every time I choose File -> Change the Config values.

This is what Device Manager Ports (COM & LPT) section looks like.

image.png

Before XTP433, the firmware showed up as May 25 (?) 2017. After may failed attempt to upload firmware, I don't even get a response to the @ver command from tera term connected to interface 3/COM8.

So I have no idea what state the SC is in.

image.png

Vivado (2019.1) hw manager can connect to the target.image.png

So, how can I resolve these issues?

Thank you

Subu

 

 

 

0 Kudos
Participant subu.rama
Participant
797 Views
Registered: ‎07-22-2018

Re: ZCU102 BOARD UI test failed!

I rebooted my Windows PC and now it shows the suggested driver versioin for Si Labs UART bridge.

image.pngimage.png

However, I can neither update the firmware nor can I run Board UI.

image.png

image.png

I can connect with tera term to interface 3 and issue @ver and see a response AFTER I power cycle the board. Once Board UI runs, it seems to be in some confused state.

image.png

Thank you

Subu

0 Kudos
Xilinx Employee
Xilinx Employee
786 Views
Registered: ‎06-21-2018

Re: ZCU102 BOARD UI test failed!

Hi subu.rama,

I wouldn't define that as a "confused state". If both the BoardUI and Tera Term try to connect to the same Serial Port, one of them won't succeed.

Please update the System Controller Firmware as explained in XTP433. You won't be able to use the latest BoardUI with the May 2017 version.

Thanks,
Andres

 

0 Kudos
Participant subu.rama
Participant
781 Views
Registered: ‎07-22-2018

Re: ZCU102 BOARD UI test failed!

I understand. However, as I have mentioned in my posts, my attempts at upgrading the firmware fail.

I can't run the 2016.4 version as suggested in a xilinx answer for this older fw version of the board either. It hangs in spite of downgrading the user drivers.

I am not running teraterm and board ui at the same time. If I exit out of the failed ui test and then power cycle the board, I can connect with teraterm.

Subu

0 Kudos
Contributor
Contributor
662 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

any update?

0 Kudos
Contributor
Contributor
658 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

Board: ZCU102_PROD
Revision: 1.0
Silicon: prod
Serial Number: 881435941911-02745
MAC Address: 00:0A:35:05:05:9A
Working in directory: ZCU102_PROD
PRESSED: Run All
Starting SYS_CTLR RESTORE at: 2019-09-03 16:15:52.891000
Starting step sysc
==========

Exception in thread Thread-2:
Traceback (most recent call last):
File "threading.py", line 801, in __bootstrap_inner
File "testthread.py", line 85, in run
File "testthread.py", line 152, in runbutton
File "testthread.py", line 520, in sysc
UnicodeEncodeError: 'ascii' codec can't encode characters in position 1-6: ordinal not in range(128)

 

abnormal.jpg

0 Kudos
Contributor
Contributor
634 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

Dear sir , does it has LINUX vertion software ? 

0 Kudos
Contributor
Contributor
633 Views
Registered: ‎10-17-2013

Re: ZCU102 BOARD UI test failed!

I disconnect USB-UART USB-JTAG cables , run the board UI software , The logging information show the same content ;

So , i'm sure the software does not wort well really!  

I install os for win 7 , win10 ;

And occured the same problem !!

0 Kudos
Newbie idmzi
Newbie
531 Views
Registered: ‎08-29-2018

Re: ZCU102 BOARD UI test failed!

I am also experiencing the same error.

I tried all the solutions the engineer gave me, but the same thing happened.

It seems to be a software problem with Python.

I get the same error message on win7 and win10.

Board : VCU128 (ES)

Vivado : 2018.3, 2019.1

OS : Windows 7, Windows 10 Korean

cf. It works fine on my co-worker's HP PC, but my two PCs fail.

0 Kudos
Xilinx Employee
Xilinx Employee
510 Views
Registered: ‎06-21-2018

Re: ZCU102 BOARD UI test failed!

Hi idmzi,

Can you show us what the error is?

Thanks,
Andres

0 Kudos