I have an existing issue with updating the firmware on a ZCU102 Rev 1.1 board as detailed in
I installed Vivado 2019.1 and repeated the process of updating the firmware. Same issue happens and the firmware does NOT update.
So, I went ahead anyway to see if the next section in XTP433 for running Board UI works.
That also has an issue. The error is a timeout waiting on a "serial port". I am not sure what serial port this is.
See the attached snapshot.
Any help in getting these two issues resolved (updating the firmware and running Board UI) is greatly appreciated. I tried with both J164 jumpered as well as left open.
Thanks
Subu
NO. That did NOT help.
The board is very much on but it now doesn't respond to the @ver command when connected to Interface 3 using tera term until a power cycle!
And I cannot update the firmware because of some errors in the script.
Sigh. It shouldn't be this hard to interface to an eval board and run canned tests.
Subu
Thank you, Deepak, but that also failed with the error: (Also the PS ERR OUT LED came out red after this)
Error: BSL Flashing Failed
Error: Found regular expression in step 2 of test 0 - "(.*)Error(.*)"
Here is the log. I pointed the Vivado path to the 2019.1 version of Vivado.
Board: ZCU102
Serial Number: 0000-0000
Mac Address: 01:02:03:04:05:06
Info: Program MSP Firmware
Version 170705_113233
2017.2 test started...
Info: The test will take 0 hours, 02 minutes, and 16 seconds. 0:02:16
Info: This step started at: 2019-08-01 16:34:00
User has confirmed: "Turn off ZCU102 Board Power.
Connect 2 jumpers across header J164 (parallel with the FMC)
Turn on ZCU102 Board Power"
step finished
Info: This step started at: 2019-08-01 16:34:40
connect -url tcp:127.0.0.1:3121
attempting to launch hw_server
****** Xilinx hw_server v2019.1
**** Build date : May 24 2019 at 15:13:31
** Copyright 1986-2019 Xilinx, Inc. All Rights Reserved.
INFO: hw_server application started
INFO: Use Ctrl-C to exit hw_server application
****** Xilinx hw_server v2019.1
**** Build date : May 24 2019 at 15:13:31
** Copyright 1986-2019 Xilinx, Inc. All Rights Reserved.
INFO: hw_server application started
INFO: Use Ctrl-C to exit hw_server application
INFO: To connect to this hw_server instance use url: TCP:127.0.0.1:3121
tcfchan#0
initializing
0% 0MB 0.0MB/s ??:?? ETA
4% 1MB 2.2MB/s ??:?? ETA
7% 1MB 1.9MB/s ??:?? ETA
10% 2MB 1.8MB/s ??:?? ETA
14% 3MB 1.8MB/s ??:?? ETA
17% 4MB 1.7MB/s ??:?? ETA
21% 5MB 1.7MB/s 00:11 ETA
24% 6MB 1.7MB/s 00:11 ETA
28% 7MB 1.7MB/s 00:10 ETA
31% 7MB 1.7MB/s 00:10 ETA
34% 8MB 1.7MB/s 00:09 ETA
38% 9MB 1.7MB/s 00:09 ETA
41% 10MB 1.7MB/s 00:08 ETA
45% 11MB 1.7MB/s 00:08 ETA
48% 12MB 1.7MB/s 00:07 ETA
51% 13MB 1.7MB/s 00:07 ETA
55% 14MB 1.7MB/s 00:06 ETA
59% 15MB 1.7MB/s 00:06 ETA
62% 15MB 1.7MB/s 00:05 ETA
66% 16MB 1.7MB/s 00:04 ETA
70% 17MB 1.7MB/s 00:04 ETA
73% 18MB 1.7MB/s 00:03 ETA
77% 19MB 1.7MB/s 00:03 ETA
81% 20MB 1.7MB/s 00:02 ETA
84% 21MB 1.7MB/s 00:02 ETA
88% 22MB 1.7MB/s 00:01 ETA
92% 23MB 1.7MB/s 00:01 ETA
96% 24MB 1.7MB/s 00:00 ETA
99% 25MB 1.7MB/s 00:00 ETA
100% 25MB 1.7MB/s 00:14
Downloading Program -- H:/XilinxDownloads/MSP_Updater (2)/Automatic/tests/ZCU102/tcl/msp_flash/periph_test.elf
section, .text: 0x00000000 - 0x000142ef
section, .init: 0x00014300 - 0x00014333
section, .fini: 0x00014340 - 0x00014373
section, .note.gnu.build-id: 0x00014374 - 0x00014397
section, .rodata: 0x00014398 - 0x00014e3f
section, .data: 0x00014e40 - 0x0001601f
section, .data1: 0x00016020 - 0x0001603f
section, .eh_frame: 0x00016040 - 0x00016043
section, .mmu_tbl0: 0x00017000 - 0x0001700f
section, .mmu_tbl1: 0x00018000 - 0x00019fff
section, .mmu_tbl2: 0x0001a000 - 0x0001dfff
section, .init_array: 0x0001e000 - 0x0001e007
section, .fini_array: 0x0001e008 - 0x0001e047
section, .sdata: 0x0001e048 - 0x0001e07f
section, .bss: 0x0001e080 - 0x0011e2bf
section, .heap: 0x0011e2c0 - 0x001262bf
section, .stack: 0x001262c0 - 0x0012f2bf
0% 0MB 0.0MB/s ??:?? ETA
86% 0MB 0.2MB/s ??:?? ETA
100% 0MB 0.2MB/s 00:00
Setting PC to Program Start Address 0x00000000
Successfully downloaded H:/XilinxDownloads/MSP_Updater (2)/Automatic/tests/ZCU102/tcl/msp_flash/periph_test.elf
step finished
Info: This step started at: 2019-08-01 16:35:10
||||||||||||||||||||
File sent successfully
Error: BSL Flashing Failed
Error: Found regular expression in step 2 of test 0 - "(.*)Error(.*)"
Info: This step started at: 2019-08-01 16:35:41
Error: Stopped because step 2 failed in test 0
Info: Result for step 0: Pass
Info: Result for step 1: Pass
Info: Result for step 2: Fail
Info: The test took 0 hours, 01 minutes, and 01 seconds. 0:01:01I ran it a second time also.
Thank you
Subu
This is specific to Deepak's response to try a package he sent me via EZMove.
I tried the same using a Windows 7 laptop with Vivado 2018.2
The program runs successfully but the MSP still is at May 25, 2017 version. It does NOT get updated to July 5, 2017.
A really stubborn MSP, this is.
Board: ZCU102
Serial Number: 0000-0000
Mac Address: 01:02:03:04:05:06
Info: Program MSP Firmware
Version 170705_113233
2017.2 test started...
Info: The test will take 0 hours, 02 minutes, and 16 seconds. 0:02:16
Info: This step started at: 2019-08-09 12:44:21
User has confirmed: "Turn off ZCU102 Board Power.
Connect 2 jumpers across header J164 (parallel with the FMC)
Turn on ZCU102 Board Power"
step finished
Info: This step started at: 2019-08-09 12:45:42
connect -url tcp:127.0.0.1:3121
attempting to launch hw_server
****** Xilinx hw_server v2018.2
**** Build date : Jun 14 2018-20:42:52
** Copyright 1986-2018 Xilinx, Inc. All Rights Reserved.
INFO: hw_server application started
INFO: Use Ctrl-C to exit hw_server application
****** Xilinx hw_server v2018.2
**** Build date : Jun 14 2018-20:42:52
** Copyright 1986-2018 Xilinx, Inc. All Rights Reserved.
INFO: hw_server application started
INFO: Use Ctrl-C to exit hw_server application
INFO: To connect to this hw_server instance use url: TCP:127.0.0.1:3121
tcfchan#0
initializing
0% 0MB 0.0MB/s ??:?? ETA
4% 1MB 2.1MB/s ??:?? ETA
7% 1MB 1.9MB/s ??:?? ETA
10% 2MB 1.8MB/s ??:?? ETA
14% 3MB 1.7MB/s ??:?? ETA
17% 4MB 1.7MB/s ??:?? ETA
20% 5MB 1.7MB/s 00:11 ETA
23% 6MB 1.7MB/s 00:11 ETA
27% 6MB 1.7MB/s 00:10 ETA
30% 7MB 1.7MB/s 00:10 ETA
33% 8MB 1.7MB/s 00:10 ETA
36% 9MB 1.7MB/s 00:09 ETA
40% 10MB 1.7MB/s 00:09 ETA
43% 10MB 1.7MB/s 00:08 ETA
46% 11MB 1.7MB/s 00:08 ETA
49% 12MB 1.7MB/s 00:07 ETA
53% 13MB 1.7MB/s 00:07 ETA
56% 14MB 1.7MB/s 00:06 ETA
59% 15MB 1.7MB/s 00:06 ETA
63% 15MB 1.7MB/s 00:05 ETA
66% 16MB 1.7MB/s 00:05 ETA
69% 17MB 1.7MB/s 00:04 ETA
72% 18MB 1.7MB/s 00:04 ETA
76% 19MB 1.6MB/s 00:03 ETA
79% 20MB 1.6MB/s 00:03 ETA
82% 20MB 1.6MB/s 00:02 ETA
85% 21MB 1.6MB/s 00:02 ETA
89% 22MB 1.6MB/s 00:01 ETA
92% 23MB 1.6MB/s 00:01 ETA
95% 24MB 1.6MB/s 00:00 ETA
98% 25MB 1.6MB/s 00:00 ETA
100% 25MB 1.6MB/s 00:15
Downloading Program -- C:/zcu102_Xilinx/MSP_Updater (2)/Automatic/tests/ZCU102/tcl/msp_flash/periph_test.elf
section, .text: 0x00000000 - 0x000142ef
section, .init: 0x00014300 - 0x00014333
section, .fini: 0x00014340 - 0x00014373
section, .note.gnu.build-id: 0x00014374 - 0x00014397
section, .rodata: 0x00014398 - 0x00014e3f
section, .data: 0x00014e40 - 0x0001601f
section, .data1: 0x00016020 - 0x0001603f
section, .eh_frame: 0x00016040 - 0x00016043
section, .mmu_tbl0: 0x00017000 - 0x0001700f
section, .mmu_tbl1: 0x00018000 - 0x00019fff
section, .mmu_tbl2: 0x0001a000 - 0x0001dfff
section, .init_array: 0x0001e000 - 0x0001e007
section, .fini_array: 0x0001e008 - 0x0001e047
section, .sdata: 0x0001e048 - 0x0001e07f
section, .bss: 0x0001e080 - 0x0011e2bf
section, .heap: 0x0011e2c0 - 0x001262bf
section, .stack: 0x001262c0 - 0x0012f2bf
0% 0MB 0.0MB/s ??:?? ETA
73% 0MB 0.2MB/s ??:?? ETA
100% 0MB 0.2MB/s 00:00
Setting PC to Program Start Address 0x00000000
Successfully downloaded C:/zcu102_Xilinx/MSP_Updater (2)/Automatic/tests/ZCU102/tcl/msp_flash/periph_test.elf
step finished
Info: This step started at: 2019-08-09 12:46:08
||||||||||||||||||||
File sent successfully
Info: This step started at: 2019-08-09 12:46:40
User has confirmed: "Turn off ZCU102 Board Power.
Remove the jumpers on J164
Turn on ZCU102 Board Power."
step finished
Info: This step started at: 2019-08-09 12:47:00
step finished
Info: This step started at: 2019-08-09 12:47:01
Info: This step started at: 2019-08-09 12:47:01
Writing: '@ver\r'
Info: This step started at: 2019-08-09 12:47:02
@ver
May 17 2017 12:51:57
>
Writing: '\x1b'
Writing: '\x08'
[('', 'MDB\rEF', '', ''), ('', 'MWB\rF2', '', ''), ('<setmux:0:75:06>', '', '', ''), ('', 'IR0\r18\r01', '', ''), ('', '\x08MWB\rF1', '', ''), ('<setmux:0:75:02>', '', '', ''), ('', 'IR1\r50\r01', '', ''), ('', '\x08MWB\rF0', '', ''), ('', 'IW1\r75\r01', '', ''), ('', 'IR1\r50\r01', '', '')]
Writing: '\t'
:R
Writing: 'MDB\rEF\r\t'
MDB
EF
:P
Writing: 'MWB\rF2\r\t'
MWB
F2
:P
Writing: 'IW0\r75\r06\r\t'
IW0
75
06
:P
Writing: 'IR0\r18\r01\r\t'
IR0
18
01
:P
Writing: '\x08MWB\rF1\r\t'
}:P
MWB
F1
:P
Writing: 'IW0\r75\r02\r\t'
IW0
75
02
:P
Writing: 'IR1\r50\r01\r\t'
IR1
50
01
Writing: '\x08MWB\rF0\r\t'
:R
MWB
F0
:P
Writing: 'IW1\r75\r01\r\t'
IW1
75
01
:P
Writing: 'IR1\r50\r01\r\t'
'@ver\r\r\nMay 17 2017 12:51:57\r\n>\r\n\x08:R\rMDB\rEF\r:P\rMWB\rF2\r:P\rIW0\r75\r06\r:P\rIR0\r18\r01\r:P\r}:P\rMWB\rF1\r:P\rIW0\r75\r02\r:P\rIR1\r50\r01\r\t:R\rMWB\rF0\r:P\rIW1\r75\r01\r:P\r'IR1
50
01
:P
Info: This step started at: 2019-08-09 12:47:21
Writing: '\x1b'
Writing: '\x08'
[('<setmux:1:74:04>', '', '', ''), ('<readsi570:1:5d>', '', '', ''), ('<calcsi570:1:5d:300:300:00>', '', '', ''), ('<setmux:1:74:00>', '', '', '')]:R
Writing: '\t'
:R
Writing: 'IW1\r74\r04\r\t'
IW1
74
04
:P
Writing: 'IW1\r5d\r8701\r\tIW1\r5d\r07\r\tIR1\r5d\r1\r\tIW1\r5d\r08\r\tIR1\r5d\r1\r\tIW1\r5d\r09\r\tIR1\r5d\r1\r\tIW1\r5d\r0a\r\tIR1\r5d\r1\r\tIW1\r5d\r0b\r\tIR1\r5d\r1\r\tIW1\r5d\r0c\r\tIR1\r5d\r1\r\tIW1\r5d\r8700\r\t'
IW1
5d
8701
:P
IW1
5d
07
:P
IR1
5d
1
:P
A0
IW1
5d
08
:P
IR1
5d
1
:P
42
IW1
5d
09
:P
IR1
5d
1
:P
F4
IW1
5d
0a
:P
IR1
5d
1
:P
0B
IW1
5d
0b
:P
IR1
5d
1
:P
51
IW1
5d
0c
:P
IR1
5d
1
:P
02
IW1
5d
8700
:P
Writing: 'IW1\r5d\r8910\r\tIW1\r5d\r07a0\r\tIW1\r5d\r0840\r\tIW1\r5d\r0900\r\tIW1\r5d\r0a00\r\tIW1\r5d\r0b00\r\tIW1\r5d\r0c00\r\tIC1\r5d\r2\r8900\r8740\r\tMWS\r00\r42a5d3ef79800000\r\t'
IW1
5d
8910
:P
IW1
5d
07a0
:P
IW1
5d
0840
:P
IW1
5d
0900
:P
IW1
5d
0a00
:P
IW1
5d
0b00
:P
IW1
5d
0c00
:P
IC1
5d
2
8900
8740
:P
MWS
00
42a5d3ef79800000
:P
Writing: 'IW1\r74\r00\r\t'
'@ver\r\r\nMay 17 2017 12:51:57\r\n>\r\n\x08:R\rMDB\rEF\r:P\rMWB\rF2\r:P\rIW0\r75\r06\r:P\rIR0\r18\r01\r:P\r}:P\rMWB\rF1\r:P\rIW0\r75\r02\r:P\rIR1\r50\r01\r\t:R\rMWB\rF0\r:P\rIW1\r75\r01\r:P\rIR1\r50\r01\r:P\r\x1b:R\r:R\rIW1\r74\r04\r:P\rIW1\r5d\r8701\r:P\rIW1\r5d\r07\r:P\rIR1\r5d\r1\r:P\rA0\rIW1\r5d\r08\r:P\rIR1\r5d\r1\r:P\r42\rIW1\r5d\r09\r:P\rIR1\r5d\r1\r:P\rF4\rIW1\r5d\r0a\r:P\rIR1\r5d\r1\r:P\r0B\rIW1\r5d\r0b\r:P\rIR1\r5d\r1\r:P\r51\rIW1\r5d\r0c\r:P\rIR1\r5d\r1\r:P\r02\rIW1\r5d\r8700\r:P\rIW1\r5d\r8910\r:P\rIW1\r5d\r07a0\r:P\rIW1\r5d\r0840\r:P\rIW1\r5d\r0900\r:P\rIW1\r5d\r0a00\r:P\rIW1\r5d\r0b00\r:P\rIW1\r5d\r0c00\r:P\rIC1\r5d\r2\r8900\r8740\r:P\rMWS\r00\r42a5d3ef79800000\r:P\r'IW1
74
00
:P
Info: This step started at: 2019-08-09 12:47:32
Writing: '\x1b'
Writing: '\x08'
[('<setmux:1:74:08>', '', '', ''), ('<readsi570:1:5d>', '', '', ''), ('<calcsi570:1:5d:156.25:156.25:01>', '', '', ''), ('<setmux:1:74:00>', '', '', '')]
Writing: '\t'
:R
Writing: 'IW1\r74\r08\r\t'
IW1
74
08
:P
Writing: 'IW1\r5d\r8701\r\tIW1\r5d\r07\r\tIR1\r5d\r1\r\tIW1\r5d\r08\r\tIR1\r5d\r1\r\tIW1\r5d\r09\r\tIR1\r5d\r1\r\tIW1\r5d\r0a\r\tIR1\r5d\r1\r\tIW1\r5d\r0b\r\tIR1\r5d\r1\r\tIW1\r5d\r0c\r\tIR1\r5d\r1\r\tIW1\r5d\r8700\r\t'
IW1
5d
8701
:P
IW1
5d
07
:P
IR1
5d
1
:P
01
IW1
5d
08
:P
IR1
5d
1
:P
C2
IW1
5d
09
:P
IR1
5d
1
:P
BC
IW1
5d
0a
:P
IR1
5d
1
:P
02
IW1
5d
0b
:P
IR1
5d
1
:P
32
IW1
5d
0c
:P
IR1
5d
1
:P
89
IW1
5d
8700
:P
Writing: 'IW1\r5d\r8910\r\tIW1\r5d\r0701\r\tIW1\r5d\r08c5\r\tIW1\r5d\r0940\r\tIW1\r5d\r0a14\r\tIW1\r5d\r0b1e\r\tIW1\r5d\r0c3c\r\tIC1\r5d\r2\r8900\r8740\r\tMWS\r01\r404dc29a261e7fce\r\t'
IW1
5d
8910
:P
IW1
5d
0701
:P
IW1
5d
08c5
:P
IW1
5d
0940
:P
IW1
5d
0a14
:P
IW1
5d
0b1e
:P
IW1
5d
0c3c
:P
IC1
5d
2
8900
8740
:P
MWS
01
404dc29a261e7fce
:P
Writing: 'IW1\r74\r00\r\t'
'@ver\r\r\nMay 17 2017 12:51:57\r\n>\r\n\x08:R\rMDB\rEF\r:P\rMWB\rF2\r:P\rIW0\r75\r06\r:P\rIR0\r18\r01\r:P\r}:P\rMWB\rF1\r:P\rIW0\r75\r02\r:P\rIR1\r50\r01\r\t:R\rMWB\rF0\r:P\rIW1\r75\r01\r:P\rIR1\r50\r01\r:P\r\x1b:R\r:R\rIW1\r74\r04\r:P\rIW1\r5d\r8701\r:P\rIW1\r5d\r07\r:P\rIR1\r5d\r1\r:P\rA0\rIW1\r5d\r08\r:P\rIR1\r5d\r1\r:P\r42\rIW1\r5d\r09\r:P\rIR1\r5d\r1\r:P\rF4\rIW1\r5d\r0a\r:P\rIR1\r5d\r1\r:P\r0B\rIW1\r5d\r0b\r:P\rIR1\r5d\r1\r:P\r51\rIW1\r5d\r0c\r:P\rIR1\r5d\r1\r:P\r02\rIW1\r5d\r8700\r:P\rIW1\r5d\r8910\r:P\rIW1\r5d\r07a0\r:P\rIW1\r5d\r0840\r:P\rIW1\r5d\r0900\r:P\rIW1\r5d\r0a00\r:P\rIW1\r5d\r0b00\r:P\rIW1\r5d\r0c00\r:P\rIC1\r5d\r2\r8900\r8740\r:P\rMWS\r00\r42a5d3ef79800000\r:P\rIW1\r74\r00\r:P\r\x08:R\rIW1\r74\r08\r:P\rIW1\r5d\r8701\r:P\rIW1\r5d\r07\r:P\rIR1\r5d\r1\r:P\r01\rIW1\r5d\r08\r:P\rIR1\r5d\r1\r:P\rC2\rIW1\r5d\r09\r:P\rIR1\r5d\r1\r:P\rBC\rIW1\r5d\r0a\r:P\rIR1\r5d\r1\r:P\r02\rIW1\r5d\r0b\r:P\rIR1\r5d\r1\r:P\r32\rIW1\r5d\r0c\r:P\rIR1\r5d\r1\r:P\r89\rIW1\r5d\r8700\r:P\rIW1\r5d\r8910\r:P\rIW1\r5d\r0701\r:P\rIW1\r5d\r08c5\r:P\rIW1\r5d\r0940\r:P\rIW1\r5d\r0a14\r:P\rIW1\r5d\r0b1e\r:P\rIW1\r5d\r0c3c\r:P\rIC1\r5d\r2\r8900\r8740\r:P\rMWS\r01\r404dc29a261e7fce\r:P\r'IW1
74
00
:P
Info: This step started at: 2019-08-09 12:47:43
Writing: '\x1b'
Writing: '\x08'
[('', 'MDB\r02', '', ''), ('<savefreq:02:0.0000001>', '', '', '')]
Writing: '\t'
:R
Writing: 'MDB\r02\r\t'
MDB
02
:P
Writing: 'MWS\r02\r3e7ad7f29abcaf48\r\t'
'@ver\r\r\nMay 17 2017 12:51:57\r\n>\r\n\x08:R\rMDB\rEF\r:P\rMWB\rF2\r:P\rIW0\r75\r06\r:P\rIR0\r18\r01\r:P\r}:P\rMWB\rF1\r:P\rIW0\r75\r02\r:P\rIR1\r50\r01\r\t:R\rMWB\rF0\r:P\rIW1\r75\r01\r:P\rIR1\r50\r01\r:P\r\x1b:R\r:R\rIW1\r74\r04\r:P\rIW1\r5d\r8701\r:P\rIW1\r5d\r07\r:P\rIR1\r5d\r1\r:P\rA0\rIW1\r5d\r08\r:P\rIR1\r5d\r1\r:P\r42\rIW1\r5d\r09\r:P\rIR1\r5d\r1\r:P\rF4\rIW1\r5d\r0a\r:P\rIR1\r5d\r1\r:P\r0B\rIW1\r5d\r0b\r:P\rIR1\r5d\r1\r:P\r51\rIW1\r5d\r0c\r:P\rIR1\r5d\r1\r:P\r02\rIW1\r5d\r8700\r:P\rIW1\r5d\r8910\r:P\rIW1\r5d\r07a0\r:P\rIW1\r5d\r0840\r:P\rIW1\r5d\r0900\r:P\rIW1\r5d\r0a00\r:P\rIW1\r5d\r0b00\r:P\rIW1\r5d\r0c00\r:P\rIC1\r5d\r2\r8900\r8740\r:P\rMWS\r00\r42a5d3ef79800000\r:P\rIW1\r74\r00\r:P\r\x08:R\rIW1\r74\r08\r:P\rIW1\r5d\r8701\r:P\rIW1\r5d\r07\r:P\rIR1\r5d\r1\r:P\r01\rIW1\r5d\r08\r:P\rIR1\r5d\r1\r:P\rC2\rIW1\r5d\r09\r:P\rIR1\r5d\r1\r:P\rBC\rIW1\r5d\r0a\r:P\rIR1\r5d\r1\r:P\r02\rIW1\r5d\r0b\r:P\rIR1\r5d\r1\r:P\r32\rIW1\r5d\r0c\r:P\rIR1\r5d\r1\r:P\r89\rIW1\r5d\r8700\r:P\rIW1\r5d\r8910\r:P\rIW1\r5d\r0701\r:P\rIW1\r5d\r08c5\r:P\rIW1\r5d\r0940\r:P\rIW1\r5d\r0a14\r:P\rIW1\r5d\r0b1e\r:P\rIW1\r5d\r0c3c\r:P\rIC1\r5d\r2\r8900\r8740\r:P\rMWS\r01\r404dc29a261e7fce\r:P\rIW1\r74\r00\r:P\r\x08:R\rMDB\r02\r:P\r'MWS
02
3e7ad7f29abcaf48
:P
Info: Result for step 0: Pass
Info: Result for step 1: Pass
Info: Result for step 2: Pass
Info: Result for step 3: Pass
Info: Result for step 4: Pass
step finished
Info: Result for step 5: Pass
Info: Result for step 6: Pass
Info: Result for step 7: Pass
Info: Result for step 8: Pass
Info: Result for step 9: Pass
Info: Result for step 10: Pass
Info: The test took 0 hours, 01 minutes, and 48 seconds. 0:01:48As can be seen in multiple places in the log, @rev produces May 17 2017
Info: This step started at: 2019-08-09 12:46:08 |||||||||||||||||||| File sent successfully Info: This step started at: 2019-08-09 12:46:40 User has confirmed: "Turn off ZCU102 Board Power. Remove the jumpers on J164 Turn on ZCU102 Board Power." step finished Info: This step started at: 2019-08-09 12:47:00 step finished Info: This step started at: 2019-08-09 12:47:01 Info: This step started at: 2019-08-09 12:47:01 Writing: '@ver\r' Info: This step started at: 2019-08-09 12:47:02 @ver May 17 2017 12:51:57
Thank you
Subu