UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Participant petr_
Participant
992 Views
Registered: ‎02-26-2013

ZCU102 SSystem controller

Jump to solution

Hi,

 

I can't connect via SCUI to configure board. 

Firmware upgrade also not work.

 

SCU via serial terminal @ver works ok.

 

Board: ZCU102
Serial Number: 0000-0000
Mac Address: 01:02:03:04:05:06


Info: SYS_CTLR v1.50 RESTORE test started...

Info: The test will take 0 hours, 01 minutes, and 23 seconds. 0:01:23

Info: This step started at: 2018-08-24 18:37:24

Info: This step started at: 2018-08-24 18:37:24

!! Press ESC to enter System Controller mode.

User has confirmed: "Turn ZCU102 Board Power Off.
Set mode switch SW6 to "0" (Up,Up,Up,Up)
Connect two jumpers across J164 as shown in XTP433
Turn ZCU102 Power On"

step finished

Info: This step started at: 2018-08-24 18:37:34
after 2000

catch { disconnect }
1
after 2000

connect -url tcp:127.0.0.1:3121
attempting to launch hw_server

****** Xilinx hw_server v2018.2
**** Build date : Jun 14 2018-20:42:52
** Copyright 1986-2018 Xilinx, Inc. All Rights Reserved.

INFO: hw_server application started
INFO: Use Ctrl-C to exit hw_server application

 

****** Xilinx hw_server v2018.2

**** Build date : Jun 14 2018-20:42:52

** Copyright 1986-2018 Xilinx, Inc. All Rights Reserved.

 

INFO: hw_server application started

INFO: Use Ctrl-C to exit hw_server application

 


INFO: To connect to this hw_server instance use url: TCP:127.0.0.1:3121

 

tcfchan#0
targets -set -filter {name =~"*APU*"}
step finished

Info: This step started at: 2018-08-24 18:37:44
Error: File could not be sent

Error: Found regular expression in step 3 of test 0 - "(.*)Error(.*)"

Error: Could not find regular expression in step 3 of test 0 - "(.*)File\s+sent\s+successfully"

Info: This step started at: 2018-08-24 18:38:04

Error: Stopped because step 3 failed in test 0

step finished

Error: Could not find regular expression in step 0 of test 0 - "(.*)MSP v1.50 I2C Bridge v1.50(.*)"

Info: Result for step 0: Fail
Info: Result for step 1: Pass
Info: Result for step 2: Pass
Info: Result for step 3: Fail
Info: The test took 0 hours, 00 minutes, and 31 seconds. 0:00:31

0 Kudos
1 Solution

Accepted Solutions
Highlighted
Visitor masoudm
Visitor
198 Views
Registered: ‎01-09-2020

Re: ZCU102 SSystem controller

Jump to solution
4 Replies
Moderator
Moderator
952 Views
Registered: ‎04-12-2017

Re: ZCU102 SSystem controller

Jump to solution

Hello @petr_,

 

Which version of SCUI are you using here ?

Please try older version of SCUI to connect board to utility.

 

Follow below answer record for more help

https://www.xilinx.com/support/answers/69640.html

 

Check device manager for successful installation of UART drivers.

 

Thank you

-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
0 Kudos
Participant petr_
Participant
928 Views
Registered: ‎02-26-2013

Re: ZCU102 SSystem controller

Jump to solution
I programmed what I need via PS IIC, SCUI remains dead.
Moderator
Moderator
899 Views
Registered: ‎06-05-2013

Re: ZCU102 SSystem controller

Jump to solution
Have you checked the device IDCODE? To ensure you are using the appropriate version of the System Controller software for the silicon on your ZCU102, check the IDCODE of the device on your board.
To do this, open the Vivado Hardware Manager and check the Hardware Device Properties.
If the first digit in the IDCODE is 2 or greater, this is production ZU9EG silicon and you should use the -C System Controller files.
If the first digit in the IDCODE is 1, then you should use the -ES2 System Controller files.

Download the correct version of SCUI from https://www.xilinx.com/products/boards-and-kits/ek-u1-zcu102-g.html#documentation

Thanks
-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
0 Kudos
Highlighted
Visitor masoudm
Visitor
199 Views
Registered: ‎01-09-2020

Re: ZCU102 SSystem controller

Jump to solution