UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Observer nicolashuger
Observer
937 Views
Registered: ‎02-20-2019

ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

Hello

I tried to boot on SD card of ZCU106 evaluation board with image from rdf0428-zcu106-vcu-trd-2019-1/images/vcu_sdirxtx and the zynq do not start.

From UART-PS0 I can see :

Xilinx Zynq MP First Stage Boot Loader
Release 2019.1 May 25 2019 - 20:50:07

But nothing else.

And ater 1 minute the led "PS_ERR_STAT" is turning on.

All the jumper are in default position.
Boot Mode is 1110

 

If I change Boot Mode to run BIST (0010) all tests pass except iic and pmod tests: 

iic test :

....

*************************************************************
** ZCU106 FMC HPC0 IIC EEPROM Test
*************************************************************
Calling iic_read

Reading EEPROM data from FMC HPC0

And UART terminal is waiting

pmod test :

********************************************************
********************************************************
** ZCU106 - PMOD Loopback Write and Read Tests **
********************************************************
********************************************************

Testing PMOD
PMOD: Writing and Reading all 0's - FAILED
Data read back = 000000FF
PMOD: Writing and Reading all 1's - PASSED
PMOD: Writing and Reading 0x55555555 pattern - FAILED
Data read back = 000000FF
PMOD: Writing and Reading 0xAAAAAAAA pattern - FAILED
Data read back = 000000FF

Completed PMOD Loopback Write and Read Tests

PMOD Test failed

At the beginning of BIST UART monitor receive

Xilinx Zynq MP First Stage Boot Loader
Release 2018.3 Jan 8 2019 - 10:18:09
PMU-FW is not running, certain applications may not be supported.

 

I tried to run ZCU106 SCUI but the log file indicate "Error: Failed to connect to Serial port"

Regards,

Nicolas

0 Kudos
1 Solution

Accepted Solutions
Observer nicolashuger
Observer
582 Views
Registered: ‎02-20-2019

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

I notice that there is a new archive : rdf0428-zcu106-vcu-trd-2019-1_v2.zip available.

With those images, the ZCU106 REV1.0 board can boot on SD card.

11 Replies
Observer nicolashuger
Observer
924 Views
Registered: ‎02-20-2019

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution
ZCU106 SCUI is working now, I have to change CP210x to CP2108 in config.json in zcu106_scui directory.
But Zynq still don't boot on SD card
0 Kudos
Moderator
Moderator
890 Views
Registered: ‎09-15-2016

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

Hi @nicolashuger 

SD card is being read as loading of FSBL flashes in the UART terminal. Are you able to read 2018.3 VCU TRD linux image or any custom boot.bin file with same SD card? Can you please share board S/N with me? Please have a look at below link for your reference as we can't conclude the same issue here so soon.

https://www.xilinx.com/support/answers/71961.html

Regards
Rohit
----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------

0 Kudos
Observer nicolashuger
Observer
875 Views
Registered: ‎02-20-2019

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

Hi Rohit

 

I am able to read 2018.3 VCU TRD linux image with the same SD card.
The S/N is 921736151913-03652 label 0432032-02-1913
Then I should have the SODIMM MTA4ATF51264HZ-2G6E1 which need to generate a new FSBL.
I will try the solution of the AR#71961 and come back to "Accept as solution" .

Thank you

Regards
Nicolas

0 Kudos
Observer nicolashuger
Observer
861 Views
Registered: ‎02-20-2019

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

Hi Rohit

I can not generate FSBL with files attached on "Xilinx Answer 72113" since I am using SDK2019.1 and DDRC_MSTR_OFFSET, DDRC_MRCTRL0_OFFSET... are unknown in FSBL src files.

According to "Xilinx Answer 72113" : this error should have been fixed in vivado 2019.1

 

Regards

Nicolas

0 Kudos
Moderator
Moderator
841 Views
Registered: ‎09-15-2016

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

Hi @nicolashuger 

Thanks for confirming the board S/N and letting us know that 2018.3 vcu trd image works fine. AR#72113 holds good for 2018.3 version. So i don't think this issue is related to new SODIMM on board. Could you run 2018.3 and 2019.1 BIT test given in XTP491 at xilinx.com.? I will also try using 2019.1 vcu trd image at my end to see if the issue is reproducible.

Regards
Rohit
----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------

0 Kudos
Observer nicolashuger
Observer
811 Views
Registered: ‎02-20-2019

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

Hi Rohit

 

I run the BIT test version 2018.3 and 2019.1

_

                    | 2018.3 | 2019.1
SYS_CTLR RESTORE    | FAILED | FAILED
IDCODE/FW Check     | PASSED | PASSED
PMBUS/EFUSE         | PASSED | PASSED
XM107 CARD TEST     | FAILED | FAILED
Test Level Shifters | PASSED | FAILED
ZCU106 RTC          | PASSED | PASSED
ZCU106 Setup        | PASSED | PASSED
WRITE EEPROM        | PASSED | PASSED
GPIO ALL            | FAILED | FAILED
IPI APP Test        | FAILED | FAILED
MIG PS DDR4         | PASSED | PASSED
MIG PL DDR4         | PASSED | PASSED
PING                | FAILED | FAILED
UART 01/02 TEST     | PASSED | PASSED
IBERT ALL           | FAILED | FAILED
Program QSPI        | PASSED | PASSED
QSPI Test           | PASSED | PASSED

_

log files of the test are attached.

 

Regards
Nicolas

 

0 Kudos
Contributor
Contributor
789 Views
Registered: ‎05-07-2018

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

I am also trying Zynq UltraScale MPSoC VCU TRD 2018.1 - Design Module 2 , and I have the same problem. I still couldn't solved it do you have any other advice?

0 Kudos
Contributor
Contributor
757 Views
Registered: ‎05-07-2018

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

Did you solve your problem? Because it is almost same as mine.

Thanks in advance.

0 Kudos
Observer nicolashuger
Observer
750 Views
Registered: ‎02-20-2019

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

No I can not run rdf0428-zcu106-vcu-trd-2019-1/images on ZCU106 evaluation board rev 1.0

But I can use rdf0428-zcu106-vcu-trd-2018-3/images on ZCU106 evaluation board rev 1.0

And I know that rdf0428-zcu106-vcu-trd-2019-1/images is working on ZCU106 evaluation board rev C (which was lending us before having the rev1.0)

Contributor
Contributor
716 Views
Registered: ‎05-07-2018

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution
Then I will apply 2018.3 version reference design module. Thank you so much.
0 Kudos
Observer nicolashuger
Observer
583 Views
Registered: ‎02-20-2019

Re: ZCU106 REV1.0 hangs when booting on SD card

Jump to solution

I notice that there is a new archive : rdf0428-zcu106-vcu-trd-2019-1_v2.zip available.

With those images, the ZCU106 REV1.0 board can boot on SD card.