cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Contributor
Contributor
561 Views
Registered: ‎05-07-2018

Zynq Ultrascale+ MPSoC VCU TRD 2018.1 SD Card Boot Error

Jump to solution

Hello,

I am really new in Ubuntu, I want to implement Zynq Ultrascale MPSoc VCU TRD 2018.1 Design Module-2 application on Zcu106 rev 1.0 Board. I installed petalinux 2018.1, I created the BOOT image , copy all the files from the $TRD_HOME/images/sdirx-vcu-sditx/ to SD card directory.

However when I insert the SD Card, I set the SW6 switches as 0111 and tried to start Zynq I just got this message on Teraterm Screen:

Xilinx Zynq MP First Stage Boot Loader
Release 2018.1 May 8 2018 - 12:21:51

In reference design page it said :

  • Power on the board; make sure INIT_B, done and all power rail LEDs are lit green.

At first INIT_B is red,after a few seconds it turns green, 

done LED which behind the INIT_B is never light up,

and after a while INIT_B turns red and PS_ERR_STAT led also lit red.

I saw the similar problems in website but either their design structures were different from mine, or their problems were still unresolved. 

I tried to apply Built in Self Test(BIST) , I  installed Vivado 2019.1  and  downloaded rdf0446-zcu106-bit-c-2019-1 zip file and made a test and there is a result:

zcu106_logzcu106_logzcu106_prod_logzcu106_prod_log

Also I want to add something, beginning of the tests ,revision option was C and it wasn't optional. During test , there are some arrangements and I couldn't make J164 jumper arrangements because I couldn't find j164 jumper in my board datasheet. Some fails may occur because of this. 

sorry for my english, I downloaded Vivado 2018.1 right now and I'm gonna try this tests again until then  I would really appreciate any help.

Thanks in advance.

 

0 Kudos
1 Solution

Accepted Solutions
Highlighted
Contributor
Contributor
458 Views
Registered: ‎05-07-2018

Re: Zynq Ultrascale+ MPSoC VCU TRD 2018.1 SD Card Boot Error

Jump to solution

Hello again,

I implemented 2018.3 reference design(before that installed 2018.3 version of petalinux and vivado ) and boot is OK now.

View solution in original post

0 Kudos
4 Replies
Highlighted
Mentor
Mentor
555 Views
Registered: ‎06-16-2013

Re: Zynq Ultrascale+ MPSoC VCU TRD 2018.1 SD Card Boot Error

Jump to solution

Hi @silat14 

 

It might be DRAM issue.

Would you refer the following ?

 

https://www.xilinx.com/support/answers/71961.html

 

Best regards,

Highlighted
Contributor
Contributor
522 Views
Registered: ‎05-07-2018

Re: Zynq Ultrascale+ MPSoC VCU TRD 2018.1 SD Card Boot Error

Jump to solution

I changed the DRAM settings and made all project again and create another BOOT file but when I tried it, it's still not working ( works exactly the same as before.)

0 Kudos
Highlighted
Contributor
Contributor
520 Views
Registered: ‎05-07-2018

Re: Zynq Ultrascale+ MPSoC VCU TRD 2018.1 SD Card Boot Error

Jump to solution

https://forums.xilinx.com/t5/Evaluation-Boards/ZCU106-REV1-0-hangs-when-booting-on-SD-card/m-p/999962#M23363

in this page,the problem is probably same as mine, but it is still unresolved.

0 Kudos
Highlighted
Contributor
Contributor
459 Views
Registered: ‎05-07-2018

Re: Zynq Ultrascale+ MPSoC VCU TRD 2018.1 SD Card Boot Error

Jump to solution

Hello again,

I implemented 2018.3 reference design(before that installed 2018.3 version of petalinux and vivado ) and boot is OK now.

View solution in original post

0 Kudos