/dts-v1/;

/ {
	#address-cells = <0x1>;
	#size-cells = <0x1>;
	compatible = "myir,zynq-myd", "xlnx,zynq-7000";
	model = "MYIR Zynq Development Board";

	cpus {
		#address-cells = <0x1>;
		#size-cells = <0x0>;

		cpu@0 {
			compatible = "arm,cortex-a9";
			device_type = "cpu";
			reg = <0x0>;
			clocks = <0x1 0x3>;
			clock-latency = <0x3e8>;
			cpu0-supply = <0x2>;
			operating-points = <0xa2c2b 0xf4240 0x51616 0xf4240>;
		};

		cpu@1 {
			compatible = "arm,cortex-a9";
			device_type = "cpu";
			reg = <0x1>;
			clocks = <0x1 0x3>;
		};
	};

	fpga-full {
		compatible = "fpga-region";
		fpga-mgr = <0x3>;
		#address-cells = <0x1>;
		#size-cells = <0x1>;
		ranges;
	};

	pmu@f8891000 {
		compatible = "arm,cortex-a9-pmu";
		interrupts = <0x0 0x5 0x4 0x0 0x6 0x4>;
		interrupt-parent = <0x4>;
		reg = <0xf8891000 0x1000 0xf8893000 0x1000>;
	};

	fixedregulator {
		compatible = "regulator-fixed";
		regulator-name = "VCCPINT";
		regulator-min-microvolt = <0xf4240>;
		regulator-max-microvolt = <0xf4240>;
		regulator-boot-on;
		regulator-always-on;
		linux,phandle = <0x2>;
		phandle = <0x2>;
	};

	amba {
		u-boot,dm-pre-reloc;
		compatible = "simple-bus";
		#address-cells = <0x1>;
		#size-cells = <0x1>;
		interrupt-parent = <0x4>;
		ranges;

		adc@f8007100 {
			compatible = "xlnx,zynq-xadc-1.00.a";
			reg = <0xf8007100 0x20>;
			interrupts = <0x0 0x7 0x4>;
			interrupt-parent = <0x4>;
			clocks = <0x1 0xc>;
		};

		can@e0008000 {
			compatible = "xlnx,zynq-can-1.0";
			status = "disabled";
			clocks = <0x1 0x13 0x1 0x24>;
			clock-names = "can_clk", "pclk";
			reg = <0xe0008000 0x1000>;
			interrupts = <0x0 0x1c 0x4>;
			interrupt-parent = <0x4>;
			tx-fifo-depth = <0x40>;
			rx-fifo-depth = <0x40>;
		};

		can@e0009000 {
			compatible = "xlnx,zynq-can-1.0";
			status = "okay";
			clocks = <0x1 0x14 0x1 0x25>;
			clock-names = "can_clk", "pclk";
			reg = <0xe0009000 0x1000>;
			interrupts = <0x0 0x33 0x4>;
			interrupt-parent = <0x4>;
			tx-fifo-depth = <0x40>;
			rx-fifo-depth = <0x40>;
		};

		gpio@e000a000 {
			compatible = "xlnx,zynq-gpio-1.0";
			#gpio-cells = <0x2>;
			clocks = <0x1 0x2a>;
			gpio-controller;
			interrupt-controller;
			#interrupt-cells = <0x2>;
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x14 0x4>;
			reg = <0xe000a000 0x1000>;
			emio-gpio-width = <0x40>;
			gpio-mask-high = <0x0>;
			gpio-mask-low = <0x5600>;
			xlnx,emio-gpio-width = <0x40>;
			xlnx,mio-gpio-mask = <0x5600>;
			linux,phandle = <0xc>;
			phandle = <0xc>;
		};

		gpio@41300000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41300000 0x10000>;
			xlnx,all-inputs = <0x1>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x0>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		axi_bram_ctrl@40000000 {
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-bram-ctrl-4.0";
			reg = <0x40000000 0x2000>;
			xlnx,bram-addr-width = <0xb>;
			xlnx,bram-inst-mode = "EXTERNAL";
			xlnx,ecc = <0x0>;
			xlnx,ecc-onoff-reset-value = <0x0>;
			xlnx,ecc-type = <0x0>;
			xlnx,fault-inject = <0x0>;
			xlnx,memory-depth = <0x800>;
			xlnx,s-axi-ctrl-addr-width = <0x20>;
			xlnx,s-axi-ctrl-data-width = <0x20>;
			xlnx,s-axi-id-width = <0x1>;
			xlnx,s-axi-supports-narrow-burst = <0x0>;
			xlnx,select-xpm = <0x1>;
			xlnx,single-port-bram = <0x1>;
		};

		gpio@412d0000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x412d0000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		gpio@412e0000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x412e0000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		gpio@412f0000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x412f0000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		serial@42c40000 {
			clock-names = "ref_clk";
			clocks = "clkc 0";
			compatible = "xlnx,axi-uartlite-2.0", "xlnx,xps-uartlite-1.00.a";
			current-speed = <0x9600>;
			device_type = "serial";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x24 0x1>;
			port-number = <0x1>;
			reg = <0x42c40000 0x10000>;
			xlnx,baudrate = <0x1c200>;
			xlnx,data-bits = <0x8>;
			xlnx,odd-parity = <0x0>;
			xlnx,s-axi-aclk-freq-hz-d = "100.0";
			xlnx,use-parity = <0x0>;
		};

		gpio@41230000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41230000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		gpio@41240000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41240000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		gpio@412b0000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x412b0000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		gpio@41210000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41210000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		serial@42c20000 {
			clock-names = "ref_clk";
			clocks = "clkc 0";
			compatible = "xlnx,axi-uartlite-2.0", "xlnx,xps-uartlite-1.00.a";
			current-speed = <0x9600>;
			device_type = "serial";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x22 0x1>;
			port-number = <0x2>;
			reg = <0x42c20000 0x10000>;
			xlnx,baudrate = <0x2580>;
			xlnx,data-bits = <0x8>;
			xlnx,odd-parity = <0x0>;
			xlnx,s-axi-aclk-freq-hz-d = "100.0";
			xlnx,use-parity = <0x0>;
		};

		gpio@41290000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41290000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		serial@42c50000 {
			clock-names = "ref_clk";
			clocks = "clkc 0";
			compatible = "xlnx,axi-uartlite-2.0", "xlnx,xps-uartlite-1.00.a";
			current-speed = <0x9600>;
			device_type = "serial";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x34 0x1>;
			port-number = <0x4>;
			reg = <0x42c50000 0x10000>;
			xlnx,baudrate = <0x2580>;
			xlnx,data-bits = <0x8>;
			xlnx,odd-parity = <0x0>;
			xlnx,s-axi-aclk-freq-hz-d = "100.0";
			xlnx,use-parity = <0x0>;
		};
		serial@42c30000 {
			clock-names = "ref_clk";
			clocks = "clkc 0";
			compatible = "xlnx,axi-uartlite-2.0", "xlnx,xps-uartlite-1.00.a";
			current-speed = <0x9600>;
			device_type = "serial";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x21 0x1>;
			port-number = <0x3>;
			reg = <0x42c30000 0x10000>;
			xlnx,baudrate = <0x2580>;
			xlnx,data-bits = <0x8>;
			xlnx,odd-parity = <0x0>;
			xlnx,s-axi-aclk-freq-hz-d = "100.0";
			xlnx,use-parity = <0x0>;
		};


		gpio@41200000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41200000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

	
		gpio@41220000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41220000 0x10000>;
			xlnx,all-inputs = <0x1>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x0>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x1>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};
		
		gpio@41270000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41270000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};
		pps-gpio {
			compatible = "pps-gpio";
			status = "okay";
			pinctrl-names = "default";
			gpios = <0x10>;
			assert-falling-edge;
		};
		gpio@41260000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41260000 0x10000>;
			xlnx,all-inputs = <0x1>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x0>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x1>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		gpio@41280000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41280000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		gpio@41250000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x41250000 0x10000>;
			xlnx,all-inputs = <0x1>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x0>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x1>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		serial@42c10000 {
			clock-names = "ref_clk";
			clocks = "clkc 0";
			compatible = "xlnx,axi-uartlite-2.0", "xlnx,xps-uartlite-1.00.a";
			current-speed = <0x9600>;
			device_type = "serial";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x23 0x1>;
			port-number = <0x5>;
			reg = <0x42c10000 0x10000>;
			xlnx,baudrate = <0x2580>;
			xlnx,data-bits = <0x8>;
			xlnx,odd-parity = <0x0>;
			xlnx,s-axi-aclk-freq-hz-d = "100.0";
			xlnx,use-parity = <0x0>;
		};

		serial@42c00000 {
			clock-names = "ref_clk";
			clocks = "clkc 0";
			compatible = "xlnx,axi-uartlite-2.0", "xlnx,xps-uartlite-1.00.a";
			current-speed = <0x9600>;
			device_type = "serial";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x20 0x1>;
			port-number = <0x6>;
			reg = <0x42c00000 0x10000>;
			xlnx,baudrate = <0x2580>;
			xlnx,data-bits = <0x8>;
			xlnx,odd-parity = <0x0>;
			xlnx,s-axi-aclk-freq-hz-d = "100.0";
			xlnx,use-parity = <0x0>;
		};

		gpio@412c0000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x412c0000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		gpio@412a0000 {
			#gpio-cells = <0x2>;
			clock-names = "s_axi_aclk";
			clocks = <0x1 0x11>;
			compatible = "xlnx,axi-gpio-2.0", "xlnx,xps-gpio-1.00.a";
			gpio-controller;
			reg = <0x412a0000 0x10000>;
			xlnx,all-inputs = <0x0>;
			xlnx,all-inputs-2 = <0x0>;
			xlnx,all-outputs = <0x1>;
			xlnx,all-outputs-2 = <0x0>;
			xlnx,dout-default = <0x0>;
			xlnx,dout-default-2 = <0x0>;
			xlnx,gpio-width = <0x1>;
			xlnx,gpio2-width = <0x20>;
			xlnx,interrupt-present = <0x0>;
			xlnx,is-dual = <0x0>;
			xlnx,tri-default = <0xffffffff>;
			xlnx,tri-default-2 = <0xffffffff>;
		};

		i2c@e0004000 {
			compatible = "cdns,i2c-r1p10";
			status = "okay";
			clocks = <0x1 0x26>;
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x19 0x4>;
			reg = <0xe0004000 0x1000>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			clock-frequency = <0x61a80>;
			xlnx,has-interrupt = <0x1>;

			adxl345@53 {
				compatible = "adi,adxl34x", "adxl34x";
				reg = <0x53>;
				interrupt-parent = <0x4>;
				interrupts = <0x0 0x1f 0x4>;
			};

			sii902x@3b {
				compatible = "sii902x";
				reg = <0x3b>;
				interrupt-parent = <0x4>;
				interrupts = <0x0 0x1d 0x4>;
				mode_str = "1920x1080";
				bits-per-pixel = <0x10>;
			};
		};

		i2c@e0005000 {
			compatible = "cdns,i2c-r1p10";
			status = "disabled";
			clocks = <0x1 0x27>;
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x30 0x4>;
			reg = <0xe0005000 0x1000>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
		};

		interrupt-controller@f8f01000 {
			compatible = "arm,cortex-a9-gic";
			#interrupt-cells = <0x3>;
			interrupt-controller;
			reg = <0xf8f01000 0x1000 0xf8f00100 0x100>;
			linux,phandle = <0x4>;
			phandle = <0x4>;
		};

		cache-controller@f8f02000 {
			compatible = "arm,pl310-cache";
			reg = <0xf8f02000 0x1000>;
			interrupts = <0x0 0x2 0x4>;
			arm,data-latency = <0x3 0x2 0x2>;
			arm,tag-latency = <0x2 0x2 0x2>;
			cache-unified;
			cache-level = <0x2>;
		};

		memory-controller@f8006000 {
			compatible = "xlnx,zynq-ddrc-a05";
			reg = <0xf8006000 0x1000>;
		};

		ocmc@f800c000 {
			compatible = "xlnx,zynq-ocmc-1.0";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x3 0x4>;
			reg = <0xf800c000 0x1000>;
		};

		serial@e0000000 {
			compatible = "xlnx,xuartps", "cdns,uart-r1p8";
			status = "okay";
			clocks = <0x1 0x17 0x1 0x28>;
			clock-names = "uart_clk", "pclk";
			reg = <0xe0000000 0x1000>;
			interrupts = <0x0 0x1b 0x4>;
			port-number = <0x1>;
			device_type = "serial";
		};

		serial@e0001000 {
			compatible = "xlnx,xuartps", "cdns,uart-r1p8";
			status = "okay";
			clocks = <0x1 0x18 0x1 0x29>;
			clock-names = "uart_clk", "pclk";
			reg = <0xe0001000 0x1000>;
			interrupts = <0x0 0x32 0x4>;
			port-number = <0x0>;
			device_type = "serial";
		};

		spi@e0006000 {
			compatible = "xlnx,zynq-spi-r1p6";
			reg = <0xe0006000 0x1000>;
			status = "disabled";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x1a 0x4>;
			clocks = <0x1 0x19 0x1 0x22>;
			clock-names = "ref_clk", "pclk";
			#address-cells = <0x1>;
			#size-cells = <0x0>;
		};

		spi@e0007000 {
			compatible = "xlnx,zynq-spi-r1p6";
			reg = <0xe0007000 0x1000>;
			status = "disabled";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x31 0x4>;
			clocks = <0x1 0x1a 0x1 0x23>;
			clock-names = "ref_clk", "pclk";
			#address-cells = <0x1>;
			#size-cells = <0x0>;
		};

		spi@e000d000 {
			clock-names = "ref_clk", "pclk";
			clocks = <0x1 0xa 0x1 0x2b>;
			compatible = "xlnx,zynq-qspi-1.0";
			status = "okay";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x13 0x4>;
			reg = <0xe000d000 0x1000>;
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			is-dual = <0x0>;
			num-cs = <0x1>;
			xlnx,fb-clk = <0x1>;
			xlnx,qspi-mode = <0x0>;

			flash@0 {
				compatible = "n25q512a", "micron,m25p80";
				reg = <0x0>;
				spi-tx-bus-width = <0x1>;
				spi-rx-bus-width = <0x4>;
				spi-max-frequency = <0x2faf080>;
				#address-cells = <0x1>;
				#size-cells = <0x1>;

				partition@qspi-boot {
					label = "qspi-boot";
					reg = <0x0 0x80000>;
				};

				partition@qspi-bootenv {
					label = "qspi-bootenv";
					reg = <0x80000 0x20000>;
				};

				partition@qspi-bitstream {
					label = "qspi-bitstream";
					reg = <0xa0000 0x460000>;
				};

				partition@qspi-kernel {
					label = "qspi-kernel";
					reg = <0x500000 0x480000>;
				};

				partition@qspi-devicetree {
					label = "qspi-devicetree";
					reg = <0x980000 0x10000>;
				};

				partition@qspi-rootfs {
					label = "qspi-rootfs";
					reg = <0x990000 0x600000>;
				};

				partition@qspi-data {
					label = "data";
					reg = <0xf90000 0x70000>;
				};
			};
		};

		memory-controller@e000e000 {
			#address-cells = <0x1>;
			#size-cells = <0x1>;
			status = "disabled";
			clock-names = "memclk", "aclk";
			clocks = <0x1 0xb 0x1 0x2c>;
			compatible = "arm,pl353-smc-r2p1";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x12 0x4>;
			ranges;
			reg = <0xe000e000 0x1000>;

			flash@e1000000 {
				status = "disabled";
				compatible = "arm,pl353-nand-r2p1";
				reg = <0xe1000000 0x1000000>;
				#address-cells = <0x1>;
				#size-cells = <0x1>;
			};

			flash@e2000000 {
				status = "disabled";
				compatible = "cfi-flash";
				reg = <0xe2000000 0x2000000>;
				#address-cells = <0x1>;
				#size-cells = <0x1>;
			};
		};

		ethernet@e000b000 {
			compatible = "cdns,zynq-gem", "cdns,gem";
			reg = <0xe000b000 0x1000>;
			status = "okay";
			interrupts = <0x0 0x16 0x4>;
			clocks = <0x1 0x1e 0x1 0x1e 0x1 0xd>;
			clock-names = "pclk", "hclk", "tx_clk";
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			phy-mode = "rgmii-id";
			phy-handle = <0x5>;

			phy@0 {
				device_type = "ethernet-phy";
				reg = <0x3>;
				linux,phandle = <0x5>;
				phandle = <0x5>;
			};
		};

		ethernet@e000c000 {
			compatible = "cdns,zynq-gem", "cdns,gem";
			reg = <0xe000c000 0x1000>;
			status = "okay";
			interrupts = <0x0 0x2d 0x4>;
			clocks = <0x1 0x1f 0x1 0x1f 0x1 0xe>;
			clock-names = "pclk", "hclk", "tx_clk";
			#address-cells = <0x1>;
			#size-cells = <0x0>;
			phy-mode = "rgmii";
			phy-handle = <0x6>;

			mdio {
				#address-cells = <0x1>;
				#size-cells = <0x0>;

				phy@0 {
					device_type = "ethernet-phy";
					reg = <0x0>;
					linux,phandle = <0x6>;
					phandle = <0x6>;
				};

				gmii_to_rgmii_0@8 {
					compatible = "xlnx,gmii-to-rgmii-1.0";
					phy-handle = <0x6>;
					reg = <0x8>;
				};
			};
		};

		mmc@e0101000 {
			compatible = "arasan,sdhci-8.9a";
			status = "okay";
			clock-names = "clk_xin", "clk_ahb";
			clocks = <0x1 0x16 0x1 0x21>;
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x2f 0x4>;
			reg = <0xe0101000 0x1000>;
			xlnx,has-cd = <0x1>;
			xlnx,has-power = <0x0>;
			xlnx,has-wp = <0x0>;
		};

		mmc@e0100000 {
			compatible = "arasan,sdhci-8.9a";
			status = "okay";
			clock-names = "clk_xin", "clk_ahb";
			clocks = <0x1 0x15 0x1 0x20>;
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x18 0x4>;
			reg = <0xe0100000 0x1000>;
			xlnx,has-cd = <0x1>;
			xlnx,has-power = <0x0>;
			xlnx,has-wp = <0x1>;
		};

		slcr@f8000000 {
			u-boot,dm-pre-reloc;
			#address-cells = <0x1>;
			#size-cells = <0x1>;
			compatible = "xlnx,zynq-slcr", "syscon", "simple-mfd";
			reg = <0xf8000000 0x1000>;
			ranges;
			linux,phandle = <0x7>;
			phandle = <0x7>;

			clkc@100 {
				u-boot,dm-pre-reloc;
				#clock-cells = <0x1>;
				compatible = "xlnx,ps7-clkc";
				fclk-enable = <0xf>;
				clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x", "cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x", "dci", "lqspi", "smc", "pcap", "gem0", "gem1", "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1", "sdio0", "sdio1", "uart0", "uart1", "spi0", "spi1", "dma", "usb0_aper", "usb1_aper", "gem0_aper", "gem1_aper", "sdio0_aper", "sdio1_aper", "spi0_aper", "spi1_aper", "can0_aper", "can1_aper", "i2c0_aper", "i2c1_aper", "uart0_aper", "uart1_aper", "gpio_aper", "lqspi_aper", "smc_aper", "swdt", "dbg_trc", "dbg_apb";
				reg = <0x100 0x100>;
				linux,phandle = <0x1>;
				phandle = <0x1>;
			};

			rstc@200 {
				compatible = "xlnx,zynq-reset";
				reg = <0x200 0x48>;
				#reset-cells = <0x1>;
				syscon = <0x7>;
			};

			pinctrl@700 {
				compatible = "xlnx,pinctrl-zynq";
				reg = <0x700 0x200>;
				syscon = <0x7>;
			};
		};

		dmac@f8003000 {
			compatible = "arm,pl330", "arm,primecell";
			reg = <0xf8003000 0x1000>;
			interrupt-parent = <0x4>;
			interrupt-names = "abort", "dma0", "dma1", "dma2", "dma3", "dma4", "dma5", "dma6", "dma7";
			interrupts = <0x0 0xd 0x4 0x0 0xe 0x4 0x0 0xf 0x4 0x0 0x10 0x4 0x0 0x11 0x4 0x0 0x28 0x4 0x0 0x29 0x4 0x0 0x2a 0x4 0x0 0x2b 0x4>;
			#dma-cells = <0x1>;
			#dma-channels = <0x8>;
			#dma-requests = <0x4>;
			clocks = <0x1 0x1b>;
			clock-names = "apb_pclk";
		};

		devcfg@f8007000 {
			compatible = "xlnx,zynq-devcfg-1.0";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x8 0x4>;
			reg = <0xf8007000 0x100>;
			clocks = <0x1 0xc 0x1 0xf 0x1 0x10 0x1 0x11 0x1 0x12>;
			clock-names = "ref_clk", "fclk0", "fclk1", "fclk2", "fclk3";
			syscon = <0x7>;
			linux,phandle = <0x3>;
			phandle = <0x3>;
		};

		efuse@f800d000 {
			compatible = "xlnx,zynq-efuse";
			reg = <0xf800d000 0x20>;
		};

		timer@f8f00200 {
			compatible = "arm,cortex-a9-global-timer";
			reg = <0xf8f00200 0x20>;
			interrupts = <0x1 0xb 0x301>;
			interrupt-parent = <0x4>;
			clocks = <0x1 0x4>;
		};

		timer@f8001000 {
			interrupt-parent = <0x4>;
			interrupts = <0x0 0xa 0x4 0x0 0xb 0x4 0x0 0xc 0x4>;
			compatible = "cdns,ttc";
			clocks = <0x1 0x6>;
			reg = <0xf8001000 0x1000>;
		};

		timer@f8002000 {
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x25 0x4 0x0 0x26 0x4 0x0 0x27 0x4>;
			compatible = "cdns,ttc";
			clocks = <0x1 0x6>;
			reg = <0xf8002000 0x1000>;
		};

		timer@f8f00600 {
			interrupt-parent = <0x4>;
			interrupts = <0x1 0xd 0x301>;
			compatible = "arm,cortex-a9-twd-timer";
			reg = <0xf8f00600 0x20>;
			clocks = <0x1 0x4>;
		};

		usb@e0002000 {
			compatible = "xlnx,zynq-usb-2.20a", "chipidea,usb2";
			status = "okay";
			clocks = <0x1 0x1c>;
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x15 0x4>;
			reg = <0xe0002000 0x1000>;
			phy_type = "ulpi";
			dr_mode = "host";
			usb-phy = <0x8>;
		};

		usb@e0003000 {
			compatible = "xlnx,zynq-usb-2.20a", "chipidea,usb2";
			status = "disabled";
			clocks = <0x1 0x1d>;
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x2c 0x4>;
			reg = <0xe0003000 0x1000>;
			phy_type = "ulpi";
		};

		watchdog@f8005000 {
			clocks = <0x1 0x2d>;
			compatible = "cdns,wdt-r1p2";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x9 0x1>;
			reg = <0xf8005000 0x1000>;
			timeout-sec = <0xa>;
		};
	};

	amba_pl {
		#address-cells = <0x1>;
		#size-cells = <0x1>;
		compatible = "simple-bus";
		ranges;

		dma@40400000 {
			#dma-cells = <0x1>;
			axistream-connected = <0x9>;
			axistream-control-connected = <0x9>;
			clock-names = "s_axi_lite_aclk", "m_axi_sg_aclk", "m_axi_mm2s_aclk", "m_axi_s2mm_aclk";
			clocks = <0x1 0x11 0x1 0x10 0x1 0x10 0x1 0x10>;
			compatible = "xlnx,eth-dma";
			interrupt-names = "mm2s_introut", "s2mm_introut";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x1d 0x4 0x0 0x1e 0x4>;
			reg = <0x40400000 0x10000>;
			xlnx,include-dre;
			linux,phandle = <0xa>;
			phandle = <0xa>;
		};

		ethernet@43c00000 {
			axistream-connected = <0xa>;
			axistream-control-connected = <0xa>;
			clock-frequency = <0x5f5e100>;
			clock-names = "s_axi_lite_clk", "axis_clk", "gtx_clk", "ref_clk";
			clocks = <0x1 0x11 0x1 0x10 0x1 0x10 0x1 0xf>;
			compatible = "xlnx,axi-ethernet-7.1", "xlnx,axi-ethernet-1.00.a";
			device_type = "network";
			interrupt-names = "interrupt";
			interrupt-parent = <0x4>;
			interrupts = <0x0 0x1f 0x4>;
			local-mac-address = [00 0a 35 04 05 06];
			phy-mode = "rgmii";
			phy-handle = <0xb>;
			reg = <0x43c00000 0x40000>;
			xlnx = <0x0>;
			xlnx,axiliteclkrate = <0x0>;
			xlnx,axisclkrate = <0x0>;
			xlnx,clockselection = <0x0>;
			xlnx,enableasyncsgmii = <0x0>;
			xlnx,gt-type = <0x0>;
			xlnx,gtinex = <0x0>;
			xlnx,gtlocation = <0x0>;
			xlnx,gtrefclksrc = <0x0>;
			xlnx,include-dre;
			xlnx,instantiatebitslice0 = <0x0>;
			xlnx,phy-type = <0x3>;
			xlnx,phyaddr = <0x1>;
			xlnx,rable = <0x0>;
			xlnx,rxcsum = <0x2>;
			xlnx,rxlane0-placement = <0x0>;
			xlnx,rxlane1-placement = <0x0>;
			xlnx,rxmem = <0x4000>;
			xlnx,rxnibblebitslice0used = <0x0>;
			xlnx,tx-in-upper-nibble = <0x1>;
			xlnx,txcsum = <0x2>;
			xlnx,txlane0-placement = <0x0>;
			xlnx,txlane1-placement = <0x0>;
			linux,phandle = <0x9>;
			phandle = <0x9>;

			mdio {
				#address-cells = <0x1>;
				#size-cells = <0x0>;

				phy@0 {
					device_type = "ethernet-phy";
					reg = <0x2>;
					linux,phandle = <0xb>;
					phandle = <0xb>;
				};
			};
		};

	};

	aliases {
		ethernet0 = "/amba/ethernet@e000b000";
		serial0 = "/amba/serial@e0001000";
		serial1 = "/amba/serial@e0000000";
		serial2 = "/serial@42c20000";
		serial3 = "/serial@42c30000";
		serial4 = "/serial@42c10000";
		serial5 = "/serial@42c40000";
		serial6 = "/serial@42c50000";
		serial7 = "/serial@42c00000";
		
	
		spi0 = "/amba/spi@e000d000";
	};

	memory {
		device_type = "memory";
		reg = <0x0 0x20000000>;
	};

	chosen {
		bootargs = "console=ttyPS0,115200 root=/dev/ram rw earlyprintk";
		linux,stdout-path = "/amba/serial@e0001000";
	};

	leds {
		compatible = "gpio-leds";

		sys_led {
			label = "sys_led";
			gpios = <0xc 0x8 0x1>;
			default-state = "off";
			linux,default-trigger = "none";
		};

		usr_led {
			label = "usr_led";
			gpios = <0xc 0x36 0x1>;
			default-state = "off";
			linux,default-trigger = "none";
		};

		gpio {
			label = "usr_gpio";
			gpios = <0xc 0x37 0x1>;
			default-state = "off";
			linux,default-trigger = "none";
		};
	};

	phy0@e0002000 {
		compatible = "ulpi-phy";
		#phy-cells = <0x0>;
		reg = <0xe0002000 0x1000>;
		view-port = <0x170>;
		drv-vbus;
		linux,phandle = <0x8>;
		phandle = <0x8>;
	};
};