UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
14,975 Views
Registered: ‎05-01-2009

Adapt PR tutorial to Virtex-4?

The PR tutorial UG744 is very nice except that it is virtex-6 based (using dsp48E component). How would one create an rp.ngc for the mult to use virtex-4 resources? There was no source for mult, just the ngc file.

 

Thanks

0 Kudos
8 Replies
Adventurer
Adventurer
14,899 Views
Registered: ‎03-02-2010

Re: Adapt PR tutorial to Virtex-4?

Found any solution yet?

0 Kudos
Highlighted
Visitor surya1985
Visitor
14,892 Views
Registered: ‎07-17-2010

Re: Adapt PR tutorial to Virtex-4?

I am looking for a video tutorial on PR using plan ahead 12.1. I found a tutorial using plan ahead 9.1 but some options seems to be different.

Tags (2)
0 Kudos
Xilinx Employee
Xilinx Employee
14,879 Views
Registered: ‎11-17-2008

Re: Adapt PR tutorial to Virtex-4?

We plan on supplying this source in the 12.3 update, but I can send it directly to you if you'd like.  Send me a PM with your email address.

0 Kudos
Xilinx Employee
Xilinx Employee
14,878 Views
Registered: ‎11-17-2008

Re: Adapt PR tutorial to Virtex-4?

Also, a video showing the path through PlanAhead for  a Partial Reconfiguration project will be posted with the relase of 12.2 (which is very soon).

0 Kudos
Visitor cuiyanzhe
Visitor
13,845 Views
Registered: ‎08-04-2011

Re: Adapt PR tutorial to Virtex-4?

Hi David,

 

Can you send me a PR tutorial to Virtex-4? my email address: cuiyanzhe841112@gmail.com

 

Thanks for your help.

0 Kudos
Xilinx Employee
Xilinx Employee
13,840 Views
Registered: ‎11-17-2008

Re: Adapt PR tutorial to Virtex-4?

Cui,

 

There is no PR tutorial specifically written for Virtex-4 (or Virtex-5), but the existing tutorials (UG743 and UG744) have HDL source that can be retargeted to those families.  Minor changes may be needed for clocking or other family-specific elements, but the flow is the same for all these families.

 

thanks,

david.

0 Kudos
Newbie g19595
Newbie
13,767 Views
Registered: ‎12-01-2011

Re: Adapt PR tutorial to Virtex-4?

Hi,

 

I've been working to adapt this tutorial for my ml505 board for a while now.  I believe I identified all the tweeks necessary and I can get to the point of generating all the bit files with no errors.  But it does not seem to be working.  I go through the whole modfied totorial with no negative feedback, but it does not boot/run/talk over uart.  My old ISE11.2 tutorial runs just fine on the same setup, so I believe the setup is fine.

 

Could someone please help me identify what must change in this tutorial using 13.2 when the target it ml505?

 

Thanks.

 

0 Kudos
Newbie g19595
Newbie
13,752 Views
Registered: ‎12-01-2011

Re: Adapt PR tutorial to Virtex-4?

David, do you have any advice to give me?

0 Kudos