UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Visitor oncu
Visitor
8,328 Views
Registered: ‎08-07-2015

XADC- Vaux7

Jump to solution

Hi,

   I have Z-7020-clg484. I am trying to read the analog signal Vaux7 by using XADC, namely IO_L7N_TI_AD2N and IO_L7P_TI_AD7P trough the pins B15 and C15 which are labeled as FMC-LA30_N and FMC-LA30_P respectively. That corresponds to 35th and 34th pins on FMC.

   My problem is I dont know how to give the input to the FMC LPC?  Should I use sth like

 

http://avnetexpress.avnet.com/store/em/EMController/Connector-Headers-and-PCB-Receptacles/Samtec-Inc/ASP-134606-01-BLK/_/R-5004319641302/A-5004319641302/An-0?action=part&catalogId=500201&langId=-1&storeId=500201&listIndex=-1&page=1&rank=0

 

or is there some special cable or adaptor that I can use to give the input?
Thanks in advance, :)
Bests,
Öncü

0 Kudos
1 Solution

Accepted Solutions
Scholar pratham
Scholar
15,867 Views
Registered: ‎06-05-2013

Re: XADC- Vaux7

Jump to solution

@oncu No problem

 

Please check this link

 

http://www.xilinx.com/products/boards-and-kits/fmc-cards.html#interfaceperipherals

-Pratham

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------
0 Kudos
5 Replies
Xilinx Employee
Xilinx Employee
8,257 Views
Registered: ‎01-03-2008

Re: XADC- Vaux7

Jump to solution

The FMC-XM105 debug card would allow you to make this connection.

------Have you tried typing your question into Google? If not you should before posting.
Too many results? Try adding site:www.xilinx.com
0 Kudos
Scholar pratham
Scholar
8,221 Views
Registered: ‎06-05-2013

Re: XADC- Vaux7

Jump to solution

@oncu Refer this UG of XM105 debug card

 

http://www.xilinx.com/support/documentation/boards_and_kits/ug537.pdf

 

Check J16 connector on debug card pin no 6 & 8 on page# 20. On these pins you can give inputs

 

 

 

-Pratham

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------
0 Kudos
Highlighted
Visitor oncu
Visitor
8,213 Views
Registered: ‎08-07-2015

Re: XADC- Vaux7

Jump to solution

The thing is that as it says in page 8 of the XM105 document, it is supported by spartan 6 and virtex-6 devices. So mine is Z-7030-clg484 Artix device. Is that a problem?

Bests,

Öncü

0 Kudos
Scholar pratham
Scholar
15,868 Views
Registered: ‎06-05-2013

Re: XADC- Vaux7

Jump to solution

@oncu No problem

 

Please check this link

 

http://www.xilinx.com/products/boards-and-kits/fmc-cards.html#interfaceperipherals

-Pratham

----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.

Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------
0 Kudos
Visitor oncu
Visitor
8,204 Views
Registered: ‎08-07-2015

Re: XADC- Vaux7

Jump to solution

Ok then, thanks :)

0 Kudos