cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
akhilchandra
Visitor
Visitor
7,179 Views
Registered: ‎10-05-2015

Licensing Problem : ./xlicclientmgr -l "format=xml"

akhil@akhil-Aspire-E1-571:~/viv/Vivado/2015.2/bin/unwrapped/lnx64.o$ ls
dccli                pcap_proxy_server         updatemem    xlicclientmgr
dsphash              saferun                   vcse_server  xlicsrvrmgr
FNPLicensingService  sg_config                 vivado       xsc
HAOPResynthWorker    svf_utility               vrs          xsim
hw_server            sysgensockgui             wbtcv        xvhdl
hw_serverpv          tclsh8.5                  xelab        xvlog
install_fnp.sh       test_rdi_burst            xilcurl
lmgrd                test_rdi_hwcosim_api      xilinxd
lmutil               unittest_sysgen_anytable  xilproxy

akhil@akhil-Aspire-E1-571:~/viv/Vivado/2015.2/bin/unwrapped/lnx64.o$ ./xlicclientmgr -l "format=xml"
ERROR: flxActCommonInit result 2   .
Exit(2) FLEXnet initialisation error.
akhil@akhil-Aspire-E1-571:~/viv/Vivado/2015.2/bin/unwrapped/lnx64.o$ xlicclientmgr -v
xlicclientmgr: command not found


0 Kudos
3 Replies
anusheel
Moderator
Moderator
7,161 Views
Registered: ‎07-21-2014

@akhilchandra

 

Check below AR:

http://www.xilinx.com/support/answers/60542.html

 

Thanks,
Anusheel
-----------------------------------------------------------------------------------------------
Search for documents/answer records related to your device and tool before posting query on forums.
Search related forums and make sure your query is not repeated.

Please mark the post as an answer "Accept as solution" in case it helps to resolve your query.
Helpful answer -> Give Kudos
-----------------------------------------------------------------------------------------------

0 Kudos
akhilchandra
Visitor
Visitor
7,157 Views
Registered: ‎10-05-2015

Thank you anusheel,

 

If my "libXLicSrvrMgrFNP.so" is in /home/viv/Vivado/2015.2/lib/lnx64.o

then to set the path I use

export PATH=$PATH://Home/viv/Vivado/2015.2/lib/lnx64.o            

I am facing a problem even If I set the path 

root@akhil-Aspire-E1-571:~/viv/Vivado/2015.2/bin/unwrapped/lnx64.o# export PATH=$PATH://Home/viv/Vivado/2015.2/lib/lnx64.o
root@akhil-Aspire-E1-571:~/viv/Vivado/2015.2/bin/unwrapped/lnx64.o# install_fnp.sh
install_fnp.sh: command not found
root@akhil-Aspire-E1-571:~/viv/Vivado/2015.2/bin/unwrapped/lnx64.o# ./xlicclientmgr –v
ERROR: –v is not a command or option.
Exit(1) error in command line.

root@akhil-Aspire-E1-571:~/viv/Vivado/2015.2/bin/unwrapped/lnx64.o# ./xlicclientmgr -l "format=xml"
ERROR: flxActCommonInit result 2   .
Exit(2) FLEXnet initialisation error.

 

0 Kudos
ashishd
Xilinx Employee
Xilinx Employee
7,145 Views
Registered: ‎02-14-2014

Hello @akhilchandra,

 

Are you using supported Linux version? Check page #9 from below UG

http://www.xilinx.com/support/documentation/sw_manuals/xilinx2015_2/ug973-vivado-release-notes-install-license.pdf 

Regards,
Ashish
----------------------------------------------------------------------------------------------
Kindly note- Please mark the Answer as "Accept as solution" if information provided is helpful.
Give Kudos to a post which you think is helpful and reply oriented.
----------------------------------------------------------------------------------------------
0 Kudos