UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Adventurer
Adventurer
1,250 Views
Registered: ‎06-27-2016

Custom ddr4 parameter for 16Gb (TwinDie-MT40A1G16KNR-062E )

Jump to solution

Hi,

I'm trying to create custom ddr4 memory part(MT40A1G16KNR-062E) for mig, This ddr4's description as per datasheet is:

"The 16Gb (TwinDie™) DDR4 SDRAM uses Micron’s 8Gb DDR4 SDRAM die; two x8s combined to
make one x16. Similar signals as mono x16, there is one extra ZQ connection for faster ZQ Calibration and
a BG1 control required for x8 addressing. Refer to Micron’s 8Gb DDR4 SDRAM data sheet (x8 option) for
the specifications not included in this document. Specifications for base part number MT40A1G8 correlate
to TwinDie manufacturing part number MT40A1G16."

 

My doubt is regarding a "Refresh Parameters By Device Density" , shall i take it wrt to 8Gb(350 ns) or 16Gb(550 ns)?

Custom parameter file and parameter table form MT40A1G8  datasheet is attached below.

 

Thank-you in advance.

0 Kudos
1 Solution

Accepted Solutions
Moderator
Moderator
1,356 Views
Registered: ‎11-28-2016

Re: Custom ddr4 parameter for 16Gb (TwinDie-MT40A1G16KNR-062E )

Jump to solution

Hello @yogesh_tripathi,

 

In these scenarios you use the timing values for the individual die, so in this case you would select the 8Gbit device timing parameters.  The DDR4 IP natively supports the MT40A1G16WBU device which is a 16Gbit twin die wide (two x8 8Gbit devices) and if you generate the IP you'll see that it sets tRFC to 350ns.

View solution in original post

4 Replies
Moderator
Moderator
1,357 Views
Registered: ‎11-28-2016

Re: Custom ddr4 parameter for 16Gb (TwinDie-MT40A1G16KNR-062E )

Jump to solution

Hello @yogesh_tripathi,

 

In these scenarios you use the timing values for the individual die, so in this case you would select the 8Gbit device timing parameters.  The DDR4 IP natively supports the MT40A1G16WBU device which is a 16Gbit twin die wide (two x8 8Gbit devices) and if you generate the IP you'll see that it sets tRFC to 350ns.

View solution in original post

Adventurer
Adventurer
699 Views
Registered: ‎04-25-2017

Re: Custom ddr4 parameter for 16Gb (TwinDie-MT40A1G16KNR-062E )

Jump to solution

Hey Yogesh,

I have been trying the exact same thing. Could you please confirm whether you have got it working?

Thanks!

Sincerely,

Maitreya Ranade.

0 Kudos
Adventurer
Adventurer
664 Views
Registered: ‎06-27-2016

Re: Custom ddr4 parameter for 16Gb (TwinDie-MT40A1G16KNR-062E )

Jump to solution
I did validated custom parameters via MIS, but couldn't verify it on hardware due to lack of hardware at that moment.
0 Kudos
Adventurer
Adventurer
655 Views
Registered: ‎04-25-2017

Re: Custom ddr4 parameter for 16Gb (TwinDie-MT40A1G16KNR-062E )

Jump to solution

Thank you very much. It surely helped. Also, how did you determine the page size? Thanks already!

0 Kudos