UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Observer galohtc
Observer
697 Views
Registered: ‎06-07-2018

Can't reset Zynq FW on VCU118

I have a VCU118 board rev2. I'm trying to burn the FW for the onboard Zynq.

i have downloaded the files from rdf0396-vcu118-system-controller-c-2018-1.zip

 

I'm following the instructions on xtp447 (pg. 57) and running the vcu118_scui\scui_v2.30\program_sysctrl script. 

 

The JTAG is identifying the Zynq but burn fails and I get the following error:

 

source {C:\\xilinx_dir\\rdf0396-vcu118-system-controller-c-2018-1\\vcu118_scui\\scui_v2.30\\program_sysctrl.tcl}
# open_hw
# catch {disconnect_hw_server localhost:3121}
# connect_hw_server -url localhost:3121
INFO: [Labtools 27-2285] Connecting to hw_server url TCP:localhost:3121
# current_hw_target [get_hw_targets */xilinx_tcf/Xilinx/*]
# set_property PARAM.FREQUENCY 6000000 [get_hw_targets */xilinx_tcf/Xilinx/*]
# open_hw_target
INFO: [Labtoolstcl 44-466] Opening hw_target localhost:3121/xilinx_tcf/Xilinx/000011e3dd0b01
# current_hw_device [get_hw_devices xc7z010_1]
# refresh_hw_device -update_hw_probes false [lindex [get_hw_devices xc7z010_1] 0]
INFO: [Labtools 27-1435] Device xc7z010 (JTAG device index = 1) is not programmed (DONE status = 0).
# create_hw_cfgmem -hw_device [lindex [get_hw_devices xc7z010_1] 0] [lindex [get_cfgmem_parts {mt25qu128-qspi-x4-single}] 0]
# set_property PROGRAM.BLANK_CHECK 0 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.ERASE 1 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.CFG_PROGRAM 1 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.VERIFY 1 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.CHECKSUM 0 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# refresh_hw_device [lindex [get_hw_devices xc7z010_1] 0]
INFO: [Labtools 27-1435] Device xc7z010 (JTAG device index = 1) is not programmed (DONE status = 0).
# set_property PROGRAM.ADDRESS_RANGE {entire_device} [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.FILES [list "BOOT_v1.60.bin" ] [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.BLANK_CHECK 0 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.ERASE 1 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.CFG_PROGRAM 1 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.VERIFY 1 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# set_property PROGRAM.CHECKSUM 0 [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
# program_hw_cfgmem -hw_cfgmem [ get_property PROGRAM.HW_CFGMEM [lindex [get_hw_devices xc7z010_1] 0]]
INFO: [Xicom 50-104] The verify operation will only be performed on the address range specified by the Memory Configuration File (MCS).
ERROR: [Labtools 27-3203] FSBL file not found. File is required to perform the configuration memory device operation.
ERROR: [Common 17-39] 'program_hw_cfgmem' failed due to earlier errors.

 

Do I need a different file other than the attached "BOOT_v1.60.bin" 

How can I solve this ? 

0 Kudos
2 Replies
Moderator
Moderator
664 Views
Registered: ‎04-12-2017

Re: Can't reset Zynq FW on VCU118

Hello @galohtc,

 

Can you please confirm which version of .bat files are you running ?

Make sure all the flying leads are connected correctly from platform cable.

 

Please follow all the steps from scratch and let us know if it helps.

 

Thank you.

-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
0 Kudos
Observer galohtc
Observer
636 Views
Registered: ‎06-07-2018

Re: Can't reset Zynq FW on VCU118

Hey @kvasantr

 

I'm using V2.3 of the .bat file. I followed all the instructions to the letter!  

All wires are connected, if the wires were not connected, it would fail much earlier, and wouldn't for example recognize the FPGA's status:

INFO: [Labtools 27-1435] Device xc7z010 (JTAG device index = 1) is not programmed (DONE status = 0).


Do you know what is the missing FSBL file needed ? 

Do you have any fix for this? 

 

Thanks 

 

0 Kudos