UPGRADE YOUR BROWSER

We have detected your current browser version is not the latest one. Xilinx.com uses the latest web technologies to bring you the best online experience possible. Please upgrade to a Xilinx.com supported browser:Chrome, Firefox, Internet Explorer 11, Safari. Thank you!

cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Visitor ksl6424
Visitor
1,700 Views
Registered: ‎10-26-2017

ZCU102 failing to multiboot from SD card

Hello, I am having difficulty using ZCU102. If you do not mind, I would appreciate your help.
I am trying to SD Multiboot from the ZCU102 ES2 (Revision 1.0). I followed everything in the document exactly.
However, I encountered the PS_ERR_OUT. The document says to check error_status registers. It was CSU_ROM error.
It is really difficult to find relevant information. To solve this problem, I need your help.

 

The documents I refer to are as follows:
1.1 ZCU102 Mutltiboot and Fallback Procedures
http://www.wiki.xilinx.com/Zynq+Ultrascale+MPSoC+Multiboot+and+Fallback
1.0 Zynq UltraScale+ MPSoC boot in Non Secure Boot
http://www.wiki.xilinx.com/x1.0%20Zynq%20UltraScale+%20MPSoC%20boot%20in%20Non%20Secure%20Boot-1.1%20ZCU102%20Hardware%20platform-1.1.4%20Programming%20the%20SD%20Card%20from%20Linux%20and%20verify%20the%20SD%20boot

 

The pre-built images I used are as follows:
Zynq 2016.4 Release
http://www.wiki.xilinx.com/Zynq+2016.4+Release
Tested images
http://www.wiki.xilinx.com/file/view/images.zip/577954885/images.zip

 

The version of Xilinx SDK and PetaLinux Tool is 2016.4.

 

Thank you for your help. 

0 Kudos
5 Replies
Moderator
Moderator
1,674 Views
Registered: ‎04-12-2017

Re: ZCU102 failing to multiboot from SD card

Hello @ksl6424,

 

Can you please post BOOSTS as well as config status register values from hardware manager ?

 

Thank you.

 

-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
Visitor ksl6424
Visitor
1,657 Views
Registered: ‎10-26-2017

Re: ZCU102 failing to multiboot from SD card

Hello @kvasantr,

 

Here is the BOOT_STATUS and CONFIG_STATUS:

 

REGISTER.BOOT_STATUS 00000000000000000000000000000000
REGISTER.BOOT_STATUS.BIT00_0_STATUS_VALID 0
REGISTER.BOOT_STATUS.BIT01_0_FALLBACK 0
REGISTER.BOOT_STATUS.BIT02_0_INTERNAL_PROG 0
REGISTER.BOOT_STATUS.BIT03_0_WATCHDOG_TIMEOUT_ERROR 0
REGISTER.BOOT_STATUS.BIT04_0_ID_ERROR 0
REGISTER.BOOT_STATUS.BIT05_0_CRC_ERROR 0
REGISTER.BOOT_STATUS.BIT06_0_WRAP_ERROR 0
REGISTER.BOOT_STATUS.BIT07_0_SECURITY_ERROR 0
REGISTER.BOOT_STATUS.BIT08_1_STATUS_VALID 0
REGISTER.BOOT_STATUS.BIT09_1_FALLBACK 0
REGISTER.BOOT_STATUS.BIT10_1_INTERNAL_PROG 0
REGISTER.BOOT_STATUS.BIT11_1_WATCHDOG_TIMEOUT_ERROR 0
REGISTER.BOOT_STATUS.BIT12_1_ID_ERROR 0
REGISTER.BOOT_STATUS.BIT13_1_CRC_ERROR 0
REGISTER.BOOT_STATUS.BIT14_1_WRAP_ERROR 0
REGISTER.BOOT_STATUS.BIT15_1_SECURITY_ERROR 0
REGISTER.BOOT_STATUS.BIT16_RESERVED 0000000000000000
REGISTER.CONFIG_STATUS 00000000000000000000000000000000
REGISTER.CONFIG_STATUS.BIT00_CRC_ERROR 0
REGISTER.CONFIG_STATUS.BIT01_DECRYPTOR_ENABLE 0
REGISTER.CONFIG_STATUS.BIT02_PLL_LOCK_STATUS 0
REGISTER.CONFIG_STATUS.BIT03_DCI_MATCH_STATUS 0
REGISTER.CONFIG_STATUS.BIT04_END_OF_STARTUP_(EOS)_STATUS 0
REGISTER.CONFIG_STATUS.BIT05_GTS_CFG_B_STATUS 0
REGISTER.CONFIG_STATUS.BIT06_GWE_STATUS 0
REGISTER.CONFIG_STATUS.BIT07_GHIGH_STATUS 0
REGISTER.CONFIG_STATUS.BIT08_MODE_PIN_M[0] 0
REGISTER.CONFIG_STATUS.BIT09_MODE_PIN_M[1] 0
REGISTER.CONFIG_STATUS.BIT10_MODE_PIN_M[2] 0
REGISTER.CONFIG_STATUS.BIT11_INIT_B_INTERNAL_SIGNAL_STATUS 0
REGISTER.CONFIG_STATUS.BIT12_INIT_B_PIN 0
REGISTER.CONFIG_STATUS.BIT13_DONE_INTERNAL_SIGNAL_STATUS 0
REGISTER.CONFIG_STATUS.BIT14_DONE_PIN 0
REGISTER.CONFIG_STATUS.BIT15_IDCODE_ERROR 0
REGISTER.CONFIG_STATUS.BIT16_SECURITY_ERROR 0
REGISTER.CONFIG_STATUS.BIT17_SYSTEM_MONITOR_OVER-TEMP_ALARM_STATUS 0
REGISTER.CONFIG_STATUS.BIT18_CFG_STARTUP_STATE_MACHINE_PHASE 000
REGISTER.CONFIG_STATUS.BIT21_SECURITY_STATUS 000
REGISTER.CONFIG_STATUS.BIT24_RESERVED 0
REGISTER.CONFIG_STATUS.BIT25_CFG_BUS_WIDTH_DETECTION 00
REGISTER.CONFIG_STATUS.BIT27_SECURITY_AUTH_ERROR 0
REGISTER.CONFIG_STATUS.BIT28_PUDC_B_PIN 0
REGISTER.CONFIG_STATUS.BIT29_BAD_PACKET_ERROR 0
REGISTER.CONFIG_STATUS.BIT30_CFGBVS_PIN 0
REGISTER.CONFIG_STATUS.BIT31_RESERVED 0

 

Thank you.

0 Kudos
Visitor ksl6424
Visitor
1,590 Views
Registered: ‎10-26-2017

Re: ZCU102 failing to multiboot from SD card

Hello @kvasantr,

 

Can you please tell me what BOOSTS is? I thought BOOSTS to be BOOT_STATUS.

Please let me know if you have any more information you need.

 

Thank you.

0 Kudos
Moderator
Moderator
1,562 Views
Registered: ‎04-12-2017

Re: ZCU102 failing to multiboot from SD card

Hello @ksl6424,

 

Thank you for sharing the asked data.

Unfortunately all the status register values are 0.

Can you please share the values after attempting programming ?

 

Also are you using any type of encryption here ?

 

Thank you.

 

-------------------------------------------------------------------------
Don’t forget to reply, kudo, and accept as solution.
-------------------------------------------------------------------------
0 Kudos
Moderator
Moderator
1,557 Views
Registered: ‎06-27-2017

Re: ZCU102 failing to multiboot from SD card

Hi,

 

I think you can read CSU boot rom err register at 0xFFD80528. you can check the TRM for error code.

 

Thanks

Kranthi

Best Regards
Kranthi
--------------------------
Don't forget to reply, kudo, and accept as solution.
0 Kudos