Xilinx Zynq MP First Stage Boot Loader Release 2018.3 Nov 21 2019 - 23:58:58 NOTICE: ATF running on XCZU3EG/silicon v4/RTL5.1 at 0xfffea000 NOTICE: BL31: Secure code at 0x0 NOTICE: BL31: Non secure code at 0x8000000 NOTICE: BL31: v1.5(release):xilinx-v2018.2-919-g08560c36 NOTICE: BL31: Built : 10:20:34, Nov 22 2019 PMUFW: v1.1 U-Boot 2018.01 (Nov 22 2019 - 11:28:01 +0000) Xilinx ZynqMP ZCU102 rev1.0 I2C: ready DRAM: 2 GiB usb dr_mode not found EL Level: EL2 Chip ID: zu3eg MMC: mmc@ff160000: 0 (eMMC), mmc@ff170000: 1 (SD) SF: Detected n25q256a with page size 512 Bytes, erase size 128 KiB, total 64 MiB In: serial@ff000000 Out: serial@ff000000 Err: serial@ff000000 Board: Xilinx ZynqMP Net: ZYNQ GEM: ff0e0000, phyaddr ffffffff, interface rgmii-id eth0: ethernet@ff0e0000 Hit any key to stop autoboot: 0 Device: mmc@ff160000 Manufacturer ID: 13 OEM: 14e Name: Q2J55 Tran Speed: 200000000 Rd Block Len: 512 MMC version 5.0 High Capacity: Yes Capacity: 7.1 GiB Bus Width: 4-bit Erase Group Size: 512 KiB HC WP Group Size: 8 MiB User Capacity: 7.1 GiB WRREL Boot Capacity: 16 MiB ENH RPMB Capacity: 4 MiB ENH reading image.ub 13604712 bytes read in 1003 ms (12.9 MiB/s) ## Loading kernel from FIT Image at 10000000 ... Using 'conf@system-top.dtb' configuration Trying 'kernel@1' kernel subimage Description: Linux kernel Type: Kernel Image Compression: gzip compressed Data Start: 0x10000104 Data Size: 7085005 Bytes = 6.8 MiB Architecture: AArch64 OS: Linux Load Address: 0x00080000 Entry Point: 0x00080000 Hash algo: sha1 Hash value: c81e3ada8d22bb44c13c4daf2f0724201ed5a196 Verifying Hash Integrity ... sha1+ OK ## Loading ramdisk from FIT Image at 10000000 ... Using 'conf@system-top.dtb' configuration Trying 'ramdisk@1' ramdisk subimage Description: petalinux-user-image Type: RAMDisk Image Compression: gzip compressed Data Start: 0x106cc1d8 Data Size: 6475774 Bytes = 6.2 MiB Architecture: AArch64 OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha1 Hash value: 07e834aef0477cf4e9b8b9d30c4526d572ddc2e7 Verifying Hash Integrity ... sha1+ OK ## Loading fdt from FIT Image at 10000000 ... Using 'conf@system-top.dtb' configuration Trying 'fdt@system-top.dtb' fdt subimage Description: Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x106c1dd8 Data Size: 41785 Bytes = 40.8 KiB Architecture: AArch64 Hash algo: sha1 Hash value: edd7999c167e88ab908814f6ced213c1a7272623 Verifying Hash Integrity ... sha1+ OK Booting using the fdt blob at 0x106c1dd8 Uncompressing Kernel Image ... OK Loading Ramdisk to 079d3000, end 07fffffe ... OK Loading Device Tree to 00000000079c5000, end 00000000079d2338 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.0-xilinx-v2018.3 (oe-user@oe-host) (gcc versio n 7.3.0 (GCC)) #1 SMP Fri Nov 22 10:23:25 UTC 2019 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Machine model: xlnx,zynqmp [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 256 MiB at 0x000000006fc00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] random: fast init done [ 0.000000] percpu: Embedded 21 pages/cpu @ffffffc07fe6d000 s46488 r8192 d313 36 u86016 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516867 [ 0.000000] Kernel command line: console=ttyPS0,115200n8 root=/dev/mmcblk1p2 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Memory: 1778512K/2096128K available (10108K kernel code, 664K rwd ata, 3224K rodata, 512K init, 2167K bss, 55472K reserved, 262144K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 M B) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 G B) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008a60000 ( 10112 K B) [ 0.000000] .rodata : 0xffffff8008a60000 - 0xffffff8008d90000 ( 3264 K B) [ 0.000000] .init : 0xffffff8008d90000 - 0xffffff8008e10000 ( 512 K B) [ 0.000000] .data : 0xffffff8008e10000 - 0xffffff8008eb6200 ( 665 K B) [ 0.000000] .bss : 0xffffff8008eb6200 - 0xffffff80090d40b0 ( 2168 K B) [ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 K B) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 M B) [ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 G B maximum) [ 0.000000] 0xffffffbf00000000 - 0xffffffbf01bfc800 ( 27 M B actual) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc07ff00000 ( 2047 M B) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU event tracing is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arch_timer: cp15 timer(s) running at 99.99MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x171015c90f, max_idle_ns: 440795203080 ns [ 0.000003] sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 43980 46511101ns [ 0.000331] Console: colour dummy device 80x25 [ 0.000355] Calibrating delay loop (skipped), value calculated using timer fr equency.. 199.99 BogoMIPS (lpj=399996) [ 0.000364] pid_max: default: 32768 minimum: 301 [ 0.000487] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000503] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.001263] ASID allocator initialised with 65536 entries [ 0.001315] Hierarchical SRCU implementation. [ 0.001652] EFI services will not be available. [ 0.001675] zynqmp_plat_init Platform Management API v1.1 [ 0.001681] zynqmp_plat_init Trustzone version v1.0 [ 0.001791] smp: Bringing up secondary CPUs ... [ 0.002073] Detected VIPT I-cache on CPU1 [ 0.002106] CPU1: Booted secondary processor [410fd034] [ 0.002409] Detected VIPT I-cache on CPU2 [ 0.002429] CPU2: Booted secondary processor [410fd034] [ 0.002707] Detected VIPT I-cache on CPU3 [ 0.002726] CPU3: Booted secondary processor [410fd034] [ 0.002771] smp: Brought up 1 node, 4 CPUs [ 0.002786] SMP: Total of 4 processors activated. [ 0.002792] CPU features: detected feature: 32-bit EL0 Support [ 0.002800] CPU: All CPU(s) started at EL2 [ 0.002816] alternatives: patching kernel code [ 0.003653] devtmpfs: initialized [ 0.008185] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns [ 0.008202] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.014390] xor: measuring software checksum speed [ 0.052058] 8regs : 2111.000 MB/sec [ 0.092090] 8regs_prefetch: 1882.000 MB/sec [ 0.132124] 32regs : 2594.000 MB/sec [ 0.172158] 32regs_prefetch: 2181.000 MB/sec [ 0.172162] xor: using function: 32regs (2594.000 MB/sec) [ 0.172255] pinctrl core: initialized pinctrl subsystem [ 0.172983] NET: Registered protocol family 16 [ 0.173779] cpuidle: using governor menu [ 0.174230] vdso: 2 pages (1 code @ ffffff8008a66000, 1 data @ ffffff8008e140 00) [ 0.174241] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.174955] DMA: preallocated 256 KiB pool for atomic allocations [ 0.197639] reset_zynqmp reset-controller: Xilinx zynqmp reset driver probed [ 0.198235] ARM CCI_400_r1 PMU driver probed [ 0.203502] zynqmp-pinctrl ff180000.pinctrl: zynqmp pinctrl initialized [ 0.212212] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.280459] raid6: int64x1 gen() 369 MB/s [ 0.348379] raid6: int64x1 xor() 409 MB/s [ 0.416489] raid6: int64x2 gen() 630 MB/s [ 0.484496] raid6: int64x2 xor() 553 MB/s [ 0.552527] raid6: int64x4 gen() 956 MB/s [ 0.620554] raid6: int64x4 xor() 680 MB/s [ 0.688626] raid6: int64x8 gen() 898 MB/s [ 0.756677] raid6: int64x8 xor() 683 MB/s [ 0.824701] raid6: neonx1 gen() 665 MB/s [ 0.892788] raid6: neonx1 xor() 781 MB/s [ 0.960834] raid6: neonx2 gen() 1071 MB/s [ 1.028886] raid6: neonx2 xor() 1106 MB/s [ 1.096942] raid6: neonx4 gen() 1381 MB/s [ 1.164982] raid6: neonx4 xor() 1321 MB/s [ 1.233023] raid6: neonx8 gen() 1514 MB/s [ 1.301077] raid6: neonx8 xor() 1405 MB/s [ 1.301081] raid6: using algorithm neonx8 gen() 1514 MB/s [ 1.301085] raid6: .... xor() 1405 MB/s, rmw enabled [ 1.301089] raid6: using neon recovery algorithm [ 1.302089] SCSI subsystem initialized [ 1.302297] usbcore: registered new interface driver usbfs [ 1.302335] usbcore: registered new interface driver hub [ 1.302378] usbcore: registered new device driver usb [ 1.302448] media: Linux media interface: v0.10 [ 1.302473] Linux video capture interface: v2.00 [ 1.302516] pps_core: LinuxPPS API ver. 1 registered [ 1.302520] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti [ 1.302537] PTP clock support registered [ 1.302563] EDAC MC: Ver: 3.0.0 [ 1.302951] zynqmp-ipi ff9905c0.mailbox: Probed ZynqMP IPI Mailbox driver. [ 1.303103] FPGA manager framework [ 1.303218] fpga-region fpga-full: FPGA Region probed [ 1.303333] Advanced Linux Sound Architecture Driver Initialized. [ 1.303636] Bluetooth: Core ver 2.22 [ 1.303667] NET: Registered protocol family 31 [ 1.303671] Bluetooth: HCI device and connection manager initialized [ 1.303680] Bluetooth: HCI socket layer initialized [ 1.303687] Bluetooth: L2CAP socket layer initialized [ 1.303704] Bluetooth: SCO socket layer initialized [ 1.304308] clocksource: Switched to clocksource arch_sys_counter [ 1.304393] VFS: Disk quotas dquot_6.6.0 [ 1.304439] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.308967] NET: Registered protocol family 2 [ 1.309316] TCP established hash table entries: 16384 (order: 5, 131072 bytes ) [ 1.309432] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 1.309726] TCP: Hash tables configured (established 16384 bind 16384) [ 1.309831] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 1.309873] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 1.310012] NET: Registered protocol family 1 [ 1.310234] RPC: Registered named UNIX socket transport module. [ 1.310239] RPC: Registered udp transport module. [ 1.310243] RPC: Registered tcp transport module. [ 1.310246] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.310355] Trying to unpack rootfs image as initramfs... [ 1.605814] Freeing initrd memory: 6320K [ 1.606297] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 1.606476] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters av ailable [ 1.607255] audit: initializing netlink subsys (disabled) [ 1.607358] audit: type=2000 audit(1.600:1): state=initialized audit_enabled= 0 res=1 [ 1.607727] workingset: timestamp_bits=62 max_order=19 bucket_order=0 [ 1.608544] NFS: Registering the id_resolver key type [ 1.608564] Key type id_resolver registered [ 1.608568] Key type id_legacy registered [ 1.608578] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.608596] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 1.637592] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 47) [ 1.637605] io scheduler noop registered [ 1.637609] io scheduler deadline registered [ 1.637629] io scheduler cfq registered (default) [ 1.637634] io scheduler mq-deadline registered [ 1.637639] io scheduler kyber registered [ 1.638975] xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed [ 1.639331] xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success [ 1.639485] xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success [ 1.639641] xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success [ 1.639796] xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success [ 1.639947] xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success [ 1.640100] xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success [ 1.640253] xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success [ 1.640430] xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success [ 1.640651] xilinx-zynqmp-dma ffa80000.dma: ZynqMP DMA driver Probe success [ 1.640805] xilinx-zynqmp-dma ffa90000.dma: ZynqMP DMA driver Probe success [ 1.640961] xilinx-zynqmp-dma ffaa0000.dma: ZynqMP DMA driver Probe success [ 1.641114] xilinx-zynqmp-dma ffab0000.dma: ZynqMP DMA driver Probe success [ 1.641270] xilinx-zynqmp-dma ffac0000.dma: ZynqMP DMA driver Probe success [ 1.641423] xilinx-zynqmp-dma ffad0000.dma: ZynqMP DMA driver Probe success [ 1.641580] xilinx-zynqmp-dma ffae0000.dma: ZynqMP DMA driver Probe success [ 1.641730] xilinx-zynqmp-dma ffaf0000.dma: ZynqMP DMA driver Probe success [ 1.670045] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.673280] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 1.678242] brd: module loaded [ 1.682629] loop: module loaded [ 1.683638] ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0 x3 impl platform mode [ 1.683649] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fb s pio slum part ccc sds apst [ 1.684775] scsi host0: ahci-ceva [ 1.685017] scsi host1: ahci-ceva [ 1.685136] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x1 00 irq 38 [ 1.685142] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x1 80 irq 38 [ 1.685334] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.686223] m25p80 spi0.0: found n25q256a, expected n25q512a [ 1.686442] m25p80 spi0.0: n25q256a (65536 Kbytes) [ 1.686462] 3 ofpart partitions found on MTD device spi0.0 [ 1.686466] Creating 3 MTD partitions on "spi0.0": [ 1.686477] 0x000000000000-0x000000100000 : "boot" [ 1.686985] 0x000000100000-0x000000140000 : "bootenv" [ 1.687411] 0x000000140000-0x000001740000 : "kernel" [ 1.688858] libphy: Fixed MDIO Bus: probed [ 1.690003] tun: Universal TUN/TAP device driver, 1.6 [ 1.690181] CAN device driver interface [ 1.690926] macb ff0e0000.ethernet: Not enabling partial store and forward [ 1.691454] libphy: MACB_mii_bus: probed [ 1.694022] macb ff0e0000.ethernet eth0: Could not attach to PHY [ 1.721119] usbcore: registered new interface driver asix [ 1.721174] usbcore: registered new interface driver ax88179_178a [ 1.721204] usbcore: registered new interface driver cdc_ether [ 1.721231] usbcore: registered new interface driver net1080 [ 1.721258] usbcore: registered new interface driver cdc_subset [ 1.721286] usbcore: registered new interface driver zaurus [ 1.721324] usbcore: registered new interface driver cdc_ncm [ 1.721652] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 1.721996] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.722002] ehci-pci: EHCI PCI platform driver [ 1.722248] usbcore: registered new interface driver uas [ 1.722284] usbcore: registered new interface driver usb-storage [ 1.722805] rtc_zynqmp ffa60000.rtc: rtc core: registered ffa60000.rtc as rtc 0 [ 1.722854] i2c /dev entries driver [ 1.723268] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 32 [ 1.723487] IR NEC protocol handler initialized [ 1.723491] IR RC5(x/sz) protocol handler initialized [ 1.723495] IR RC6 protocol handler initialized [ 1.723499] IR JVC protocol handler initialized [ 1.723503] IR Sony protocol handler initialized [ 1.723507] IR SANYO protocol handler initialized [ 1.723510] IR Sharp protocol handler initialized [ 1.723514] IR MCE Keyboard/mouse protocol handler initialized [ 1.723518] IR XMP protocol handler initialized [ 1.724853] usbcore: registered new interface driver uvcvideo [ 1.724857] USB Video Class driver (1.1.1) [ 1.725362] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at ffffff800915 d000 with timeout 60s [ 1.725608] cdns-wdt ff150000.watchdog: Xilinx Watchdog Timer at ffffff800916 5000 with timeout 10s [ 1.725785] Bluetooth: HCI UART driver ver 2.3 [ 1.725792] Bluetooth: HCI UART protocol H4 registered [ 1.725796] Bluetooth: HCI UART protocol BCSP registered [ 1.725823] Bluetooth: HCI UART protocol LL registered [ 1.725827] Bluetooth: HCI UART protocol ATH3K registered [ 1.725832] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 1.725874] Bluetooth: HCI UART protocol Intel registered [ 1.725878] Bluetooth: HCI UART protocol QCA registered [ 1.725914] usbcore: registered new interface driver bcm203x [ 1.725949] usbcore: registered new interface driver bpa10x [ 1.725982] usbcore: registered new interface driver bfusb [ 1.726015] usbcore: registered new interface driver btusb [ 1.726020] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 1.726074] usbcore: registered new interface driver ath3k [ 1.726207] EDAC MC: ECC not enabled [ 1.726364] EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac control ler zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT) [ 1.726894] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1099999 KHz [ 1.726949] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1199999 KHz [ 1.727358] sdhci: Secure Digital Host Controller Interface driver [ 1.727363] sdhci: Copyright(c) Pierre Ossman [ 1.727366] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.772321] mmc0: SDHCI controller on ff160000.mmc [ff160000.mmc] using ADMA 64-bit [ 1.772363] PLL: shutdown [ 1.772429] PLL: enable [ 1.824313] mmc1: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit [ 1.831933] ledtrig-cpu: registered to indicate activity on CPUs [ 1.832101] usbcore: registered new interface driver usbhid [ 1.832105] usbhid: USB HID core driver [ 1.834260] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 1.835881] usbcore: registered new interface driver snd-usb-audio [ 1.836678] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 1.838397] Netfilter messages via NETLINK v0.30. [ 1.838525] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.838618] mmc0: new HS200 MMC card at address 0001 [ 1.838894] Initializing XFRM netlink socket [ 1.838969] NET: Registered protocol family 10 [ 1.839253] mmcblk0: mmc0:0001 Q2J55L 7.09 GiB [ 1.839351] mmcblk0boot0: mmc0:0001 Q2J55L partition 1 16.0 MiB [ 1.839435] mmcblk0boot1: mmc0:0001 Q2J55L partition 2 16.0 MiB [ 1.839471] Segment Routing with IPv6 [ 1.839520] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.839522] mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB [ 1.841065] mmcblk0: p1 [ 1.841209] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.841563] NET: Registered protocol family 17 [ 1.841577] NET: Registered protocol family 15 [ 1.841595] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.841601] Ebtables v2.0 registered [ 1.843929] can: controller area network core (rev 20170425 abi 9) [ 1.843973] NET: Registered protocol family 29 [ 1.843979] can: raw protocol (rev 20170425) [ 1.843985] can: broadcast manager protocol (rev 20170425 t) [ 1.843992] can: netlink gateway (rev 20170425) max_hops=1 [ 1.844057] Bluetooth: RFCOMM TTY layer initialized [ 1.844066] Bluetooth: RFCOMM socket layer initialized [ 1.844077] Bluetooth: RFCOMM ver 1.11 [ 1.844091] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.844095] Bluetooth: BNEP filters: protocol multicast [ 1.844104] Bluetooth: BNEP socket layer initialized [ 1.844109] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.844115] Bluetooth: HIDP socket layer initialized [ 1.844270] 9pnet: Installing 9P2000 support [ 1.844290] Key type dns_resolver registered [ 1.844735] registered taskstats version 1 [ 1.845118] Btrfs loaded, crc32c=crc32c-generic [ 1.850226] ff000000.serial: ttyPS0 at MMIO 0xff000000 (irq = 41, base_baud = 6249999) is a xuartps [ 1.873816] mmc1: new high speed SDHC card at address 1234 [ 1.874098] mmcblk1: mmc1:1234 SA08G 7.21 GiB (ro) [ 1.875111] mmcblk1: p1 p2 [ 1.998503] ata1: SATA link down (SStatus 0 SControl 330) [ 2.002492] ata2: SATA link down (SStatus 0 SControl 330) [ 3.503698] console [ttyPS0] enabled [ 3.507775] ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 42, base_baud = 6249999) is a xuartps [ 3.518163] xilinx-psgtr fd400000.zynqmp_phy: Lane:3 type:8 protocol:4 pll_lo cked:yes [ 3.526362] PLL: shutdown [ 3.528978] zynqmp_pll_disable() clock disable failed for dpll_int, ret = -13 [ 3.536190] PLL: shutdown [ 3.539218] PLL: enable [ 3.541775] PLL: shutdown [ 3.545282] More than two devices are using the vpll, which is forbidden [ 3.552013] ------------[ cut here ]------------ [ 3.556635] WARNING: CPU: 2 PID: 61 at /kernel-source//drivers/clk/zynqmp/pll .c:218 zynqmp_pll_set_rate+0x250/0x288 [ 3.567054] Modules linked in: [ 3.570106] CPU: 2 PID: 61 Comm: kworker/2:1 Not tainted 4.14.0-xilinx-v2018. 3 #1 [ 3.577575] Hardware name: xlnx,zynqmp (DT) [ 3.581758] Workqueue: events deferred_probe_work_func [ 3.586889] task: ffffffc06dadcf00 task.stack: ffffff80092a8000 [ 3.592802] PC is at zynqmp_pll_set_rate+0x250/0x288 [ 3.597758] LR is at zynqmp_pll_set_rate+0x250/0x288 [ 3.602713] pc : [] lr : [] pstate: 60000 145 [ 3.610099] sp : ffffff80092ab7c0 [ 3.613406] x29: ffffff80092ab7c0 x28: 0000000000000000 [ 3.618709] x27: 0000000000000000 x26: 0000000000000000 [ 3.624013] x25: 0000000000000060 x24: 0000000000000060 [ 3.629317] x23: ffffffc06db17e80 x22: 0000000001fca055 [ 3.634620] x21: ffffffc06db17e80 x20: ffffff8008b732f0 [ 3.639924] x19: 000000005ad20000 x18: 0000000000000010 [ 3.645227] x17: 0000000000000001 x16: 0000000000000000 [ 3.650530] x15: ffffffffffffffff x14: ffffff8088ebf237 [ 3.655834] x13: ffffff8008e18aa8 x12: ffffff800851a2b0 [ 3.661137] x11: 0000000005f5e0ff x10: 0000000000000007 [ 3.666441] x9 : 00000000ffffffd0 x8 : 206863696877202c [ 3.671744] x7 : 6c6c707620656874 x6 : 0000000000000139 [ 3.677048] x5 : 0000000000000064 x4 : 0000000000000000 [ 3.682352] x3 : 0000000000000000 x2 : ffffffffffffffff [ 3.687655] x1 : ffffff8008e2cf08 x0 : 000000000000003c [ 3.692959] Call trace: [ 3.695399] Exception stack(0xffffff80092ab680 to 0xffffff80092ab7c0) [ 3.701833] b680: 000000000000003c ffffff8008e2cf08 ffffffffffffffff 00000000 00000000 [ 3.709653] b6a0: 0000000000000000 0000000000000064 0000000000000139 6c6c7076 20656874 [ 3.717474] b6c0: 206863696877202c 00000000ffffffd0 0000000000000007 00000000 05f5e0ff [ 3.725295] b6e0: ffffff800851a2b0 ffffff8008e18aa8 ffffff8088ebf237 ffffffff ffffffff [ 3.733115] b700: 0000000000000000 0000000000000001 0000000000000010 00000000 5ad20000 [ 3.740936] b720: ffffff8008b732f0 ffffffc06db17e80 0000000001fca055 ffffffc0 6db17e80 [ 3.748757] b740: 0000000000000060 0000000000000060 0000000000000000 00000000 00000000 [ 3.756577] b760: 0000000000000000 ffffff80092ab7c0 ffffff80084bbfa8 ffffff80 092ab7c0 [ 3.764398] b780: ffffff80084bbfa8 0000000060000145 0000000000000003 ffffff80 08ef5000 [ 3.772219] b7a0: ffffffffffffffff ffffff0000000000 ffffff80092ab7c0 ffffff80 084bbfa8 [ 3.780041] [] zynqmp_pll_set_rate+0x250/0x288 [ 3.786038] [] clk_change_rate+0x1a8/0x270 [ 3.791688] [] clk_core_set_rate_nolock+0x64/0xd8 [ 3.797946] [] clk_set_rate+0x30/0x50 [ 3.803168] [] xilinx_dp_codec_probe+0xe0/0x228 [ 3.809249] [] platform_drv_probe+0x58/0xb8 [ 3.814987] [] driver_probe_device+0x22c/0x2d8 [ 3.820985] [] __device_attach_driver+0x9c/0xf8 [ 3.827069] [] bus_for_each_drv+0x4c/0x98 [ 3.832633] [] __device_attach+0xc0/0x138 [ 3.838197] [] device_initial_probe+0x10/0x18 [ 3.844108] [] bus_probe_device+0x94/0xa0 [ 3.849672] [] device_add+0x390/0x598 [ 3.854890] [] of_device_add+0x38/0x48 [ 3.860192] [] of_platform_device_create_pdata+0x84/0xe8 [ 3.867058] [] of_platform_bus_create+0x120/0x348 [ 3.873317] [] of_platform_populate+0x7c/0xe8 [ 3.879227] [] zynqmp_dpsub_probe+0xc8/0x168 [ 3.885051] [] platform_drv_probe+0x58/0xb8 [ 3.890790] [] driver_probe_device+0x22c/0x2d8 [ 3.896787] [] __device_attach_driver+0x9c/0xf8 [ 3.902872] [] bus_for_each_drv+0x4c/0x98 [ 3.908436] [] __device_attach+0xc0/0x138 [ 3.914001] [] device_initial_probe+0x10/0x18 [ 3.919911] [] bus_probe_device+0x94/0xa0 [ 3.925475] [] deferred_probe_work_func+0xa0/0x148 [ 3.931823] [] process_one_work+0x1dc/0x348 [ 3.937558] [] worker_thread+0x24c/0x488 [ 3.943036] [] kthread+0x12c/0x130 [ 3.947992] [] ret_from_fork+0x10/0x18 [ 3.953292] ---[ end trace 6029c33fa1b21e60 ]--- [ 3.958315] PLL: enable [ 3.960859] xilinx-dp-snd-codec fd4a0000.zynqmp-display:zynqmp_dp_snd_codec0: Xilinx DisplayPort Sound Codec probed [ 3.971554] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PC M probed [ 3.979591] xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PC M probed [ 3.987994] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xi linx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok [ 4.000436] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: xi linx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok [ 4.013112] xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: Xi linx DisplayPort Sound Card probed [ 4.023292] OF: graph: no port node found in /amba/zynqmp-display@fd4a0000 [ 4.030303] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 4.036905] [drm] No driver support for vblank timestamp query. [ 4.042889] xlnx-drm xlnx-drm.0: bound fd4a0000.zynqmp-display (ops 0xffffff8 008b17868) [ 4.081578] [drm] Cannot find any crtc or sizes [ 4.086289] [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.zynqmp-display on minor 0 [ 4.094389] zynqmp-display fd4a0000.zynqmp-display: ZynqMP DisplayPort Subsys tem driver probed [ 4.103244] dwc3-of-simple ff9d0000.usb0: dwc3_simple_set_phydata: Can't find usb3-phy [ 4.112169] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 4.117664] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus nu mber 1 [ 4.125548] xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks 0x22010010 [ 4.134266] xhci-hcd xhci-hcd.0.auto: irq 48, io mem 0xfe200000 [ 4.140321] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.147101] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 4.154312] usb usb1: Product: xHCI Host Controller [ 4.159181] usb usb1: Manufacturer: Linux 4.14.0-xilinx-v2018.3 xhci-hcd [ 4.165874] usb usb1: SerialNumber: xhci-hcd.0.auto [ 4.171030] hub 1-0:1.0: USB hub found [ 4.174791] hub 1-0:1.0: 1 port detected [ 4.178895] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 4.184379] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus nu mber 2 [ 4.192076] usb usb2: We don't know the algorithms for LPM for this host, dis abling LPM. [ 4.200240] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 4.207020] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 4.214238] usb usb2: Product: xHCI Host Controller [ 4.219110] usb usb2: Manufacturer: Linux 4.14.0-xilinx-v2018.3 xhci-hcd [ 4.225801] usb usb2: SerialNumber: xhci-hcd.0.auto [ 4.230912] hub 2-0:1.0: USB hub found [ 4.234674] hub 2-0:1.0: 1 port detected [ 4.238784] dwc3 fe200000.dwc3: couldn't register cable notifier [ 4.244789] dwc3 fe200000.dwc3: failed to initialize dual-role [ 4.250642] platform fe200000.dwc3: runtime PM trying to suspend device but a ctive child [ 4.258725] dwc3: probe of fe200000.dwc3 failed with error -22 [ 4.265448] rtc_zynqmp ffa60000.rtc: setting system clock to 2019-11-22 11:23 :59 UTC (1574421839) [ 4.274319] of_cfs_init [ 4.276781] of_cfs_init: OK [ 4.279804] PLL: shutdown [ 4.283339] ALSA device list: [ 4.286301] #0: DisplayPort monitor [ 4.290515] Freeing unused kernel memory: 512K INIT: version 2.88 booting Starting udev [ 4.411440] udevd[1779]: starting version 3.2.2 [ 4.420969] udevd[1780]: starting eudev-3.2.2 [ 4.783832] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 4.881235] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. O pts: (null) Fri Nov 22 11:29:17 UTC 2019 Starting internet superserver: inetd. Configuring packages on first boot.... (This may take several minutes. Please do not power off the machine.) Running postinst /etc/rpm-postinsts/100-sysvinit-inittab... update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing) INIT: Entering runlevel: 5 Configuring network interfaces... Cannot find device "eth0" Starting Dropbear SSH server: Generating key, this may take a while... Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCD4qvhROWTtRWvRMTB7iH7zRlKbWcVRpPb8G8Gsn+v PBQfz+sirZlbl3CQ7ekCmqZmM+akgpEPbLEZz80fxFWkDkGGXmpDrRzLGbdKLCzTbh2E300Pd+Bn4+kU urLd7+43ir1Oyando3i5GNoyEgR36MlcivObZM43RsNn707tExKuQdyIL9fd3s0dBr0z2SvL0u0ExcHG uEZx0j65xq1Zf7TkS70qiILzxc0ZfWsmircpSNv2n4HqDSQGUTqeEYzIQ5xYCJX9VDO4TncqOQgziuSN VxkE5pgDocEnW7Zev1FiNg1lVmNB2adeRYaDhTKvi06XE5FPamhWSVrITujX root@ultrazed_test Fingerprint: md5 15:31:dc:18:da:e0:d0:24:0a:2f:4f:6d:b5:c3:85:a7 dropbear. Starting syslogd/klogd: done Starting tcf-agent: OK PetaLinux 2018.3 ultrazed_test /dev/ttyPS0 ultrazed_test login: